Oil Filter (Implement Pilot) (Front Pump Drive) - Remove and Install
Removal Procedure
Start By:
- Release the hydraulic system pressure. Refer to Disassembly and Assembly, " Hydraulic System Pressure - Release".
Note: Cap all hydraulic lines and fittings that are disconnected in order to prevent oil loss. This will also keep contaminants out of the hydraulic system.
- Remove cover (1) .
Show/hide table
Illustration 1 | g01423427 |
- Remove channel (2) .
Show/hide table
Illustration 2 | g01423429 |
- Disconnect hose assemblies (3) and (4) from each filter assembly.
Show/hide table
Illustration 3 | g01423454 |
- Disconnect harness assemblies (5), (6), and (7) .
Show/hide table
Illustration 4 | g01423455 |
- Attach Tooling (A) and a suitable lifting device to hydraulic oil filters (9). The weight of hydraulic oil filters (9) is approximately 17 kg (37 lb). Remove bolts (8) and hydraulic oil filters (9) .
Show/hide table
Illustration 5 | g01423457 |
Installation Procedure
- Attach Tooling (A) and a suitable lifting device to hydraulic oil filters (9). The weight of hydraulic oil filters (9) is approximately 17 kg (37 lb). Install hydraulic oil filters (9) and bolts (8) .
Show/hide table
Illustration 6 | g01423457 |
- Connect harness assemblies (5), (6), and (7) .
Show/hide table
Illustration 7 | g01423455 |
- Connect hose assemblies (3) and (4) to each filter assembly.
Show/hide table
Illustration 8 | g01423454 |
- Install channel (2) .
Show/hide table
Illustration 9 | g01423429 |
- Install cover (1) .
Show/hide table
Illustration 10 | g01423427 |
Caterpillar Information System:
994F Wheel Loader Fuel Tank Water and Sediment - Drain
994F Wheel Loader Frame - Inspect
3176C and 3196 Engines for Caterpillar Built Machines Fuel Lines
994F Wheel Loader VIMS Payload Control System
3176C and 3196 Engines for Caterpillar Built Machines Turbocharger
854K Wheel Dozer and 992K Wheel Loader Fuel Cooler - Remove and Install
C6.6 Engines For Caterpillar Built Machines Ignition Keyswitch Circuit and Battery Supply Circuit - Test
Parts and Installation of the 315-5321 Drive Shaft Kit {3253} Parts and Installation of the 315-5321 Drive Shaft Kit {3253}
Field Assembly of 854K Wheel Dozer{7000, 7960} Field Assembly of 854K Wheel Dozer{7000, 7960}
Field Assembly of 992K Wheel Loader{7000, 7960} Field Assembly of 992K Wheel Loader{7000, 7960}
993K Wheel Loader Power Train Axle Oil Cooler Pump and Motor
938H Wheel Loader and IT38H Integrated Toolcarrier Hydraulic System Oil Coolers and Cooling System Operation
994F Wheel Loader Radiator Core - Clean
3176C and 3196 Engines for Caterpillar Built Machines Fuel Lines
2007/11/05 Replacement of the Priming Pump {1258, 1263}
2008/04/07 An Improved Motor For The Air Conditioning Condenser Is Now Available {1805, 1815, 5927, 7320}
Parts and Installation of the 284-3875 Drive Shaft Kit {3253} Parts and Installation of the 284-3875 Drive Shaft Kit {3253}
2007/10/15 Improved Quality Of Center Crossmember {6107}
2007/10/15 A New Spring Pin Is Used on the Bracket for the Warning Beacon {1431}
2007/10/15 Improved Mounting For Air Conditioning Compressor {1802, 7320}
319D Excavator Hydraulic System Relief Valve (Pilot)
IT38H Integrated Toolcarrier and 938H Wheel Loader Braking and Hydraulic Fan System Hydraulic Fan Speed - Test and Adjust
Procedure to Improve Alignment of the Left Door on Medium Wheel Loaders{7308} Procedure to Improve Alignment of the Left Door on Medium Wheel Loaders{7308}
2009/07/27 Improvements Have Been Made to the Automatic Lubrication System (Hydraulic Actuated Systems) {7540}