Transmission Oil Pump - Install
Show/hide table
| Required Tools | |||
|---|---|---|---|
| Tool | Part Number | Part Description | Qty |
| A | 8C-8422 | Sealant | 1 |
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.
- Apply Tooling (A) to transmission oil pump (3), as shown.
- Install transmission oil pump (3) and bolts (2). Tighten bolts (2) to a torque of
55 ± 10 N·m (41 ± 7 lb ft) . - Connect tube assembly (5).
- Connect hose assemblies (1), (4), and (6).
Show/hide table
| |
| Illustration 1 | g01266067 |
Show/hide table
| |
| Illustration 2 | g01266059 |
End By:
- Install the cab floorplate. Refer to Disassembly and Assembly, "Floorplate - Remove and Install".
Caterpillar Information System:
525C, 535C and 545C Wheel Skidders Power Train Transmission Oil Pump - Remove
992G Wheel Loader and 854G Wheel Dozer Power Train Speed Sensor (Transmission Output)
Underground Articulated Trucks Truck Payload Measurement System System Components
Underground Articulated Trucks Truck Payload Measurement System Calibration
Underground Articulated Trucks Truck Payload Measurement System General Information
AccuGrade® GPS (CD700) System Components
C27 and C32 Engines for Caterpillar Built Machines Camshaft - Install - C27
C27 and C32 Engines for Caterpillar Built Machines Cylinder Head - Install - C27
C27 and C32 Engines for Caterpillar Built Machines Cylinder Head - Remove - C27
C27 and C32 Engines for Caterpillar Built Machines Flywheel Housing - Remove and Install - C27
C27 and C32 Engines for Caterpillar Built Machines Valve Mechanism Cover - Remove and Install - C27
C27 and C32 Engines for Caterpillar Built Machines Fuel Filter Base - Install - C27
525C, 535C and 545C Wheel Skidders Machine Systems Pilot Oil Accumulator (Dead Engine Lower) - Remove and Install
Filtration Procedure for (D7- D11) Track-Type Tractor Hydraulic Oil {0680, 0738, 0768, 5050, 5056} Filtration Procedure for (D7- D11) Track-Type Tractor Hydraulic Oil {0680, 0738, 0768, 5050, 5056}
525C, 535C and 545C Wheel Skidders Machine Systems Control Manifold (Pilot) (Differential Lock) - Remove
525C, 535C and 545C Wheel Skidders Machine Systems Control Manifold (Pilot) (Differential Lock) - Install
525C, 535C and 545C Wheel Skidders Machine Systems Control Manifold (Pilot) (Differential Lock) - Disassemble
525C, 535C and 545C Wheel Skidders Machine Systems Control Manifold (Pilot) (Differential Lock) - Assemble
938H and IT38H Wheel Loader and Integrated Tool Carrier Power Train Pressure Switch (Power Train Oil Filter Bypass)
2006/05/08 Improved Design For Alternator Guard {7168}
525C, 535C and 545C Wheel Skidders Machine Systems Cab - Remove
938H and IT38H Wheel Loader and Integrated Tool Carrier Power Train Transmission Hydraulic Control
525C, 535C and 545C Wheel Skidders Machine Systems Cab - Install
C9 On-highway Engine Electronic Unit Injector Wiring