D8T Track-Type Tractor Caterpillar


Ether Starting Aid Cylinder - Replace

Usage:

D8T J8B

------ ПРЕДУПРЕЖДЕНИЕ! ------

Вдишване на етерни изпарения или няколкократен контакт на етер с кожата може да доведе до трудови злополуки. Трудова злополука или смърт може да бъде причинена от неспазването на следните процедури.

Използвайте етер само в добре проветрени помещения.

Не пушете, когато сменяте флакони с етер.

Използвайте етер внимателно, за да избегнете пожари.

Не съхранявайте резервни флакони с етер в жилищни помещения или в отделението на оператора.

Не съхранявайте флакони с етер на пряка слънчева светлина или на температури превишаващи 49° C (120°F).

Изхвърляйте флаконите на безопасно място. Не пробивайте и не палете флакони.

Дръжте флаконите с етер на места недостъпни за неупълномощени лица.

За да избегнете евентуални злополуки, убедете се, че спирачките са включени и всички органи за управление са в положения Задържане или Неутрално, когато пускате двигателя.




Илюстрация 1g01018416

  1. Отворете люка за достъп (ако е монтиран) до двигателя отляво на машината. Флаконът с етер е монтиран в отсека от страната на двигателя


    Илюстрация 2g01018418

  2. Разхлабете крепежната скоба. Извадете стария флакон, като го завъртите обратно на часовниковата стрелка.

  3. Свалете използваната гарнитура. Поставете новата гарнитура.

  4. Поставете новия флакон. Завъртете флакона по посока на часовниковата стрелка. Затегнете флакона на ръка. Затегнете скобата около флакона.

  5. Затворете люка за достъп до двигателя (ако е монтиран).

Caterpillar Information System:

994D Wheel Loader Cooling System Coolant Level - Check
C11 and C15 Engines for Caterpillar Built Machines CID 0102 FMI 04 Boost Pressure Sensor short to ground
D8T Track-Type Tractor Fuses and Circuit Breakers - Replace/Reset
994D Wheel Loader Welding on Machines and Engines with Electronic Controls
2003/08/25 A New Solenoid Provides Better Starting Conditions {1259}
2003/08/25 A New Latch Assembly Is Used on the Wheel Skidders {7251}
Installation and Removal of the V-PAT Bulldozer{6050} Installation and Removal of the V-PAT Bulldozer{6050}
583T Pipelayer Engine Oil Sample - Obtain
583T Pipelayer Engine Oil Level - Check
2004/09/27 A New Solid Retaining Ring Replaces The Spiral Lock Ring in the Transmission Clutches {3030, 3155}
2004/09/27 New Check Valve For The Ride Control System {5067}
583T Pipelayer Engine Crankcase Breather - Clean
2003/09/01 Correction to Testing and Adjusting , "Margin Pressure Adjustment Procedure" {4306, 5070, 5086}
D8T Track-Type Tractor Final Drive Oil - Change
D8T Track-Type Tractor Final Drive Oil Level - Check
D8T Track-Type Tractor Fuel System - Prime
C27 and C32 Engines for Caterpillar Built Machines CID 0342 FMI 08 Secondary Engine Speed signal abnormal
C27 and C32 Engines for Caterpillar Built Machines CID 0172 FMI 03 Intake Manifold Air Temp open/short to +batt
C27 and C32 Engines for Caterpillar Built Machines CID 0172 FMI 04 Intake Manifold Air Temp short to ground
C27 and C32 Engines for Caterpillar Built Machines CID 0262 FMI 03 5 Volt Sensor DC Power Supply short to +batt
C27 and C32 Engines for Caterpillar Built Machines CID 0262 FMI 04 5 Volt Sensor DC Power Supply short to ground
C11 and C15 Engines for Caterpillar Built Machines CID 0190 FMI 08 Engine Speed signal abnormal
C15 and C18 Engines for Caterpillar Built Machines CID 1834 FMI 02 Ignition Key Switch loss of signal
C27 and C32 Engines for Caterpillar Built Machines CID 0261 FMI 13 Engine Timing Calibration required
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.