621G Wheel Tractor-Scraper Caterpillar


Engine Oil Level - Check

Usage:

621G CEN

------ WARNING! ------

Hot oil and hot components can cause personal injury. Do not allow hot oil or hot components to contact skin.

----------------------


NOTICE

Do not under fill or overfill engine crankcase with oil. Either condition can cause engine damage.





Illustration 1g00667764

The dipstick (1) for the tractor engine is located on the right side of the tractor.

  1. Park the machine on level ground. Lower the bowl.

  1. Open the engine access cover that is on the right side of the machine.

  1. Check the "LOW IDLE" side of dipstick (1) while the engine is running. Maintain the oil level between the "ADD" mark and the "FULL" mark.

    Check the "ENGINE STOPPED" side of dipstick (1) while the engine is stopped. Maintain the oil level between the "LOW" mark and the "FULL" mark.




    Illustration 2g00759441

    Note: When you operate the machine on severe slopes, the oil level in the engine crankcase must be at the "FULL" mark on the "ENGINE STOPPED" side of the dipstick (1) .

  1. Clean the oil filler cap (2). Remove the oil filler cap. If necessary, add oil.

  1. Clean the oil filler cap and install the oil filler cap.

  1. Close the engine access cover.

Caterpillar Information System:

637G Wheel Tractor-Scraper Steering Pump Outlet Screen - Clean
621G and 627G Wheel Tractor-Scrapers Hydraulic System Ejector
621G and 627G Wheel Tractor-Scrapers Hydraulic System Draft Frame
621G and 627G Wheel Tractor-Scrapers Hydraulic System Check Valve (Carry and Quick-Drop)
3516B Engine for Caterpillar Built Machines Diagnostic Codes
621G, 623G, 627G, 631G, 637G, and 657G Wheel Tractor-Scrapers Power Train Electronic Control System Using Caterpillar Monitoring System to Determine Diagnostic Codes
631G and 637G Wheel Tractor-Scrapers Hydraulic System Sequence and Pressure Control Valve (Apron)
H35E S, H45E S, H55E S and H65E S Hydraulic Hammers Work Tool - Inspect/Recondition
657G Wheel Tractor-Scraper Backup Alarm - Test
623G Wheel Tractor-Scraper Monitoring System
657G Wheel Tractor-Scraper Hydraulic System Pilot Control Actuator (Apron, Bowl, and Ejector)
IT28G Integrated Toolcarrier and 924G, 924GZ, 928G and 930G Wheel Loaders Engine Crankcase Breather (Closed Circuit) - Replace - If Equipped
D5N Track-Type Tractor Capacities (Refill)
637G Wheel Tractor-Scraper Transmission Breathers - Clean
637G Wheel Tractor-Scraper Transmission Oil Filter and Magnetic Screen - Replace/Clean
637G Wheel Tractor-Scraper Transmission Oil Sample - Obtain
637G Wheel Tractor-Scraper Cooling System Coolant Sample (Level 1) - Obtain
637G Wheel Tractor-Scraper Engine Air Filter Service Indicator - Inspect
3516B Generator Set Engines with Dynamic Gas Blending Grounding Practices
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Hydraulic System Hydraulic Fan System
621G, 623G, 627G, 631G, 637G, and 657G Wheel Tractor-Scrapers Power Train Electronic Control System Using Caterpillar Electronic Technician to Determine Diagnostic Codes
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Braking System Vane Pump (Braking)
621G and 627G Wheel Tractor-Scrapers Hydraulic System Pump Control Valve (Cushion-Hitch) - Test and Adjust
621G, 623G, 627G, 631G, 637G, and 657G Wheel Tractor-Scrapers Power Train Electronic Control System Power Supply Circuit of Electronic Control Module
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.