Priority Valve - Test and Adjust
Show/hide table
Required Tools     | ||
---|---|---|
Part Number     | Part Description     | Qty     |
6V-7830     | Tetragauge group     | 1     |
The priority valve is located beneath the floorplate in the operator compartment.
- Attach the gauge to pressure tap (PV) .
Show/hide table
Illustration 1 | g00887540 |
D5N and D6N with FTC CBF1-299 CCG1-399 ALH1-734 CBJ1-399 ALR1-634 AGG1-1334 AKD1-1134 CFH1-0299 CKT1-0399 |
Show/hide table
Illustration 2 | g01248831 |
D5N with FTC AKD1135-Up AGG1335-Up CFH0300-Up CKT0400-Up |
Show/hide table
Illustration 3 | g01167618 |
D6N with FTC CBF300-Up CCG400-Up ALH735-Up CBJ400-Up ALR635-Up |
- Warm the transmission oil to operating temperature.
- Move the parking brake switch to the Off position.
- Run the engine at LOW IDLE. Note the pressure on the gauge. The pressure should be 2925 ± 125 kPa (424 ± 18 psi).
- If the pressure that is observed is not 2925 ± 125 kPa (424 ± 18 psi), perform the following steps:
- Move the parking brake switch to the On position. Shut off the engine.
- Loosen locknut (2) .
Show/hide tableIllustration 4 g00937223
Priority valve
- Turn adjustment screw (1) clockwise in order to increase the pressure setting. Turn adjustment screw (1) counterclockwise in order to decrease the pressure setting.
Note: Turn adjustment screw (1) counterclockwise past the desired pressure setting. Then, turn adjustment screw (1) clockwise to the correct pressure setting. This method of adjustment eliminates any movement in the threads.
- Tighten locknut (2) to a torque of 25 ± 4 N·m (18 ± 3 lb ft).
- Repeat Steps 3 through 5.
Caterpillar Information System:
D5N Track-Type Tractor Power Train Relief Valve (Torque Converter Inlet) Pressure - Test and Adjust
D6N Track-Type Tractor Power Train Relief Valve (Torque Converter Outlet) Pressure - Test and Adjust
2002/06/03 Underground Articulated Trucks are now Shipped with TDTO SAE 30W Oil {1000, 7000, 7581}
2002/06/03 New Clamps Improve Scavenge Pump Tube Service Life {3016, 3154}
D5N Track-Type Tractor Power Train Relief Valve (Transmission) - Test and Adjust
D6N Track-Type Tractor Power Train Pressure Charts
IT28G Integrated Toolcarrier and 924G, 924GZ and 928G Wheel Loaders Power Train Data Link
IT28G Integrated Toolcarrier and 924G, 924GZ and 928G Wheel Loaders MID 081 - CID 0096 - FMI 04
D5N Track-Type Tractor Power Train General Testing and Adjusting Information
D5N Track-Type Tractor Power Train Visual Inspection
545 Wheel Skidder Window Washer Reservoir - Fill
814F Wheel Dozer, 815F Soil Compactor and 816F Landfill Compactor Power Train MID 081 - CID 1711 - FMI 04
2002/06/03 Announcing the Combination of Groups Within the Paper Copies of the Caterpillar Parts Manuals {0374}
D5N Track-Type Tractor Power Train Speed Sensor - Adjust
D5N Track-Type Tractor Power Train Troubleshooting
IT28G Integrated Toolcarrier and 924G, 924GZ and 928G Wheel Loaders MID 081 - CID 0070 - FMI 04
IT28G Integrated Toolcarrier and 928G Wheel Loader Hydraulic System General Information
IT28G Integrated Toolcarrier and 924G, 924GZ and 928G Wheel Loaders MID 081 - CID 0177 - FMI 03
IT28G Integrated Toolcarrier and 924G, 924GZ and 928G Wheel Loaders MID 081 - CID 0177 - FMI 04
IT28G Integrated Toolcarrier and 924G, 924GZ and 928G Wheel Loaders MID 081 - CID 0426 - FMI 04
IT28G Integrated Toolcarrier and 924G, 924GZ and 928G Wheel Loaders MID 081 - CID 0473 - FMI 04
IT28G Integrated Toolcarrier and 924G, 924GZ and 928G Wheel Loaders MID 081 - CID 0177 - FMI 08
IT28G Integrated Toolcarrier and 924G, 924GZ and 928G Wheel Loaders MID 081 - CID 1401 - FMI 03
IT28G Integrated Toolcarrier and 924G, 924GZ and 928G Wheel Loaders MID 081 - CID 1402 - FMI 03