Bucket Links - Install
安装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A     | 1U-9200     | 操纵杆滚轮起重机     | 2     |
F     | 1P-0520     | 冲头总成     | 1     |
G     | 9U-7289     | 量尺     | 1     |
H     | 5P-3931     | 防粘结剂     | 1     |
J     | 5P-0960     | 润滑脂筒     | 1     |
Show/hide table
图 1 | g00686497 |
注: 对于本程序中提及的销和销接头,请用图 1 作为参照。
注: 如果安装了新销,请参阅拆解和组装, "铲斗 - 安装"以了解磨合程序。
- 彻底清洁铲斗连杆的所有孔。
- 使用绝缘手套操作轴承 (11) 。
注: 以下步骤用于将轴承安装在铲斗连杆的 C 销孔中。
Show/hide table
图 2 | g01141149 |
Show/hide table
图 3 | g01141151 |
- 安装之前,将轴承 (11) 的温度冷却至 −73°C (−100°F)。
- 使用工具 (F) 和工具 (G) ,将轴承 (11) 安装在每个铲斗连杆中。
注: 将铲斗连杆 C 销接头的轴承 (11) 安装至深度为 11.0 ± 0.5 mm (0.43 ± 0.02 in)。
- 对其余铲斗连杆重复步骤1 和 4。
- 使用绝缘手套操作轴承 (10) 。
注: 以下步骤用于将轴承安装在铲斗连杆的 E 销孔中。
Show/hide table
图 4 | g01141156 |
Show/hide table
图 5 | g01141157 |
- 安装之前,将轴承 (10) 的温度冷却至 −73°C (−100°F)。
- 使用工具 (F) 和工具 (G) ,将轴承 (10) 安装在铲斗连杆的 E 销中。
注: 将铲斗连杆 E 销孔的轴承 (10) 安装至深度为 11.0 ± 0.5 mm (0.43 ± 0.02 in)。
- 对其余铲斗连杆重复步骤6 至 8。
- 将两个唇型密封 (9) 安装到 E 销的接头轴承中。
注: 确保密封唇方位正确。
Show/hide table
图 6 | g00703859 |
Show/hide table
图 7 | g00704115 |
校准唇型密封的方位。 |
- 将两个唇型密封 (9) 安装到 C 销的接头轴承中。 对其余铲斗连杆重复步骤8 和 11。
- 彻底清洁铲斗上的孔。 把工具 (H) 涂抹在孔上。
Show/hide table
图 8 | g00703810 |
Show/hide table
图 9 | g00703811 |
- 将适当的起吊设备连接到右侧铲斗连杆 (5) 上。 铲斗连杆 (5) 的重量约为 263 kg (580 lb)。
- 安装右侧铲斗连杆 (5) 。
- 需要两个人安装 C 销 (8) 。 C 销的重量为 29 kg (64 lb)。
- 安装板 (7) 、螺栓 (6) 和垫圈。
- 安装左侧铲斗连杆时重复步骤12 至 15。
注: C 销 (8) 在轴承孔内采用滑动配合。 必须正确对准铲斗连杆和铲斗上的孔。 安装 C 销 (8) 时请勿过度用力。
- 如图所示,将工具 (A) 连接到铲斗连杆 (3) 和 (5) 上。
Show/hide table
图 10 | g00703807 |
Show/hide table
图 11 | g00705558 |
- 使用工具 (A) 以便对齐倾斜油缸 E 销和铲斗连杆的孔。
- 将适当的起吊设备连接在 E 销 (4) 上。 E 销的重量约为 92 kg (203 lb)。
- 安装 E 销 (4) 。
注: E 销 (4) 在轴承孔内采用滑动配合。 必须正确对准铲斗连杆和倾斜油缸上的孔。 安装 E 销 (4) 时请勿过度用力。
- 连接润滑脂管 (2) 。
Show/hide table
图 12 | g00703672 |
- 向润滑脂加注嘴加注工具 (J) ,直到润滑脂渗出唇型密封。
End By: 安装动臂连杆。 请参阅 拆解和组装, "动臂连杆 - 安装"。
Caterpillar Information System:
D8R Series II Track-Type Tractor Engine Supplement Vibration Damper and Pulley - Remove and Install
988G Wheel Loader Electrohydraulic System MID 082 - CID 0499 - FMI 05
D7R Series II Track-Type Tractor Transmission Breather - Clean
525B Wheel Skidder and 535B Wheel Skidder Power Train Differential Lock Pressure - Check
651E and 657E Wheel Tractor-Scrapers Power Train Transmission Hydraulic Control Operation
988G Wheel Loader Electrohydraulic System MID 082 - CID 0499 - FMI 03
525B Wheel Skidder and 535B Wheel Skidder Power Train Axle Housing and Bearing Preload - Adjust
525B Wheel Skidder and 535B Wheel Skidder Power Train Differential Backlash and Bearings - Adjust
834G Wheel Dozer and 836G Landfill Compactor Electrohydraulic System MID 082 - CID 0498 - FMI 13
SR4 and SR4B Electric Power Generation Rewind Data Winding Data for <B>5N-9081</B> Generator through <B>5N-9432</B> Generator
980G Wheel Loader, 824G Wheel Dozer, 825G Soil Compactor and 826G Landfill Compactor Implement Electronic Control System MID 082 - CID 0498 - FMI 06
525B Wheel Skidder and 535B Wheel Skidder Power Train Differential Pinion Preload - Adjust
D7R Series II Track-Type Tractor Walk-Around Inspection
980G Wheel Loader, 824G Wheel Dozer, 825G Soil Compactor and 826G Landfill Compactor Implement Electronic Control System MID 082 - CID 0358 - FMI 03
980G Wheel Loader, 824G Wheel Dozer, 825G Soil Compactor and 826G Landfill Compactor Implement Electronic Control System MID 082 - CID 0358 - FMI 05
980G Wheel Loader, 824G Wheel Dozer, 825G Soil Compactor and 826G Landfill Compactor Implement Electronic Control System MID 082 - CID 0358 - FMI 06
988G Wheel Loader Electrohydraulic System MID 082 - CID 0499 - FMI 06
973C Track-Type Loader Power Train Track - Connect
966G and 972G Wheel Loaders Logging Fork Clamp Control - If Equipped
651E and 657E Wheel Tractor-Scrapers Power Train Differential and Bevel Gear
854G Wheel Tractor and 992G Wheel Loader Engine Supplement Water Temperature Regulator - Remove
966G and 972G Wheel Loaders Engine Air Filter Service Indicator - Inspect/Replace
854G Wheel Tractor and 992G Wheel Loader Engine Supplement Water Temperature Regulator - Install
973C Track-Type Loader Power Train Front Idler and Yoke - Remove