Case Drain Oil Filters - Replace - If Equipped
Show/hide table
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products. Dispose of all fluids according to local regulations and mandates. |
Show/hide table
| |
| Illustration 1 | g00680707 |
|
View Toward Rear (1) Steering pump. (2) Fan pump. | |
The two case drain filters are located under the access door in the platform behind the cab.
- Stop the engine.
- Use a strap type wrench to remove the filter element. Dispose of the used filter element properly.
- Clean the filter mounting base. Make sure that all of the used gasket is removed from the filter mounting base.
- Lubricate the gasket of the new filter element with clean hydraulic oil.
- Install the new filter by hand. When the gasket contacts the filter base, tighten the filter by an additional 3/4 turn.
- Repeat the above steps for the other case drain filter.
- Start the engine and run the engine at low idle. Operate the steering, the brakes, and the implements.
- Stop the engine. Inspect the filters for leaks. Make any necessary repairs.
Caterpillar Information System:
2000/02/28 New Springs Increase Service Life {1265}
3408E and 3412E Engines for Caterpillar Built Machines E100 Low Engine Oil Pressure Warning
D6F SR, D6G and D6G SR Track-Type Tractors Drive Shaft Universal Joint - Lubricate
D6F SR, D6G and D6G SR Track-Type Tractors Bulldozer Tilt Brace - Lubricate - If Equipped
3408E and 3412E Engines for Caterpillar Built Machines Inlet Manifold Pressure - Test
3456 Engine, 836G Landfill Compactor, 834G Wheel Dozer and 988G Wheel Loader E098 Engine Prelube Override
3456 Engine, 836G Landfill Compactor, 834G Wheel Dozer and 988G Wheel Loader E035 Loss of Coolant Flow Warning
D6F SR, D6G and D6G SR Track-Type Tractors Cooling System Additive - Add
3408E and 3412E Engines for Caterpillar Built Machines Turbocharger - Inspect
3408E and 3412E Engines for Caterpillar Built Machines Inlet Air Temperature Sensor
3126B and 3126E Truck Engine Cooling System - Check - Overheating
854G Wheel Dozer Machine Systems Piston Motor (Hydraulic Fan) - Assemble
988G Wheel Loader Power Train Transmission Planetary - Assemble
988G Wheel Loader Machine Systems Maintenance Free Linkage Seals - Install
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0289 - FMI 02 Unfiltered Fuel Pressure misinstalled
3126B Engines Connecting Rod Bearings - Inspect
988G Wheel Loader Electrohydraulic System Solenoid Valve (Pilot Pressure Supply)
3126B and 3126E Truck Engine Main Bearings - Inspect
D6F SR, D6G and D6G SR Track-Type Tractors Sprocket Hub Bearings - Adjust
D6F SR, D6G and D6G SR Track-Type Tractors Engine Valve Lash - Check
988G Wheel Loader Electrohydraulic System Pilot Control Actuator
H35E S, H35 S, H45E S, H45S, H55E S, H55S, H65E S and H65S Hydraulic Hammers Visual Inspection
988G Wheel Loader Electrohydraulic System Relief Valve (Main)
3126B Engines Flywheel - Inspect