Balancer Group (Front) - Remove and Install - 3508B Engine
拆卸步骤
Show/hide table
| 所需工具 | |||
| 工具 | 零件号 | 零件描述 | 数量 |
| A | 1P-0520 | 起子总成 | 1 |
开始:
- 拆卸前壳体。 请参阅拆解和组装, "前壳体 - 拆卸和安装"。
Show/hide table
| 注意 |
|---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 拆下螺栓 (3) 和止推盘 (4) 。
Show/hide table
 | |
| 图 1 | g01135236 |
- 从齿轮轴 (2) 上卸下平衡轴齿轮 (5) 。
- 使用工具 (A) 和合适的压具从平衡轴齿轮 (5) 上拆卸套筒轴承 (6) 。
- 将螺栓 (1) 和齿轮轴 (2) 从缸体前部拆下。
安装步骤
Show/hide table
| 所需工具 | |||
| 工具 | 零件号 | 零件描述 | 数量 |
| A | 1P-0520 | 起子总成 | 1 |
Show/hide table
| 注意 |
|---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 使用工具 (A) 和合适的压具在平衡轴齿轮 (5) 内安装套筒轴承 (6) 。
注: 必须加工套筒轴承 (6) 以达到正确的内径。 请参阅专门说明书, SEHS9282, "对替换套筒轴承的加工"。
Show/hide table
| | |
| 图 2 | g01135236 |
- 安装齿轮轴 (2) 和螺栓 (1) 。 拧紧螺栓 (1) 至扭矩为 140 ± 10 N·m (103 ± 7 lb ft)。
- 将干净的发动机油涂抹在平衡器齿轮 (5) 的套筒轴承和齿轮轴 (2) 上。 将平衡轴齿轮 (5) 安装到齿轮轴 (2) 上。 确保平衡器齿轮 (5) 和曲轴齿轮上的标记与发动机转动对齐。 安装止推板 (4) 和螺栓 (3) 。
End By: 安装前壳体。 请参阅 拆解和组装, "前壳体 - 拆卸和安装"。
Caterpillar Information System:
C11 and C15 Engines for Caterpillar Built Machines E096 High Fuel Pressure
2013/09/02 A New Strainer Assembly For the Hydraulic Tank Is Now Available {5056, 5068}
C11 and C13 Engines for Caterpillar Built Machines Fan Drive Mounting Group - Remove and Install
C32 Marine Engines Event Codes
C11 and C13 Engines for Caterpillar Built Machines Crankshaft Position Sensor - Remove and Install
311B, 312B, 315B, 320B, 322B, 325B and 330B Excavators Air Conditioning and Heating Manifold Gauge Set (Refrigerant) - Remove
3508B, 3512B and 3516B Generator Set Engines Engine Oil Sequence Valves - Remove and Install
3412E Petroleum Engine Diagnostic Code Cross Reference
3412E Petroleum Engine Intermittent Engine Shutdown
C11 and C13 Engines for Caterpillar Built Machines Engine Oil Pressure Sensor - Remove and Install
C11 and C13 Engines for Caterpillar Built Machines Camshaft Position Sensor - Remove and Install
C11 and C13 Engines for Caterpillar Built Machines Atmospheric Pressure Sensor - Remove and Install
3412E Petroleum Engine CID 0110 FMI 03 Engine Coolant Temperature open/short to +batt
3412E Petroleum Engine CID 0110 FMI 04 Engine Coolant Temperature short to ground
311B, 312B, 315B, 320B, 322B, 325B and 330B Excavators Air Conditioning and Heating Refrigerant System - Flush
311B, 312B, 315B, 320B, 322B, 325B and 330B Excavators Air Conditioning and Heating Refrigerant Recovery
311B, 312B, 315B, 320B, 322B, 325B and 330B Excavators Air Conditioning and Heating Required Tools
311B, 312B, 315B, 320B, 322B, 325B and 330B Excavators Air Conditioning and Heating Manifold Gauge Set (Refrigerant) - Install
311B, 312B, 315B, 320B, 322B, 325B and 330B Excavators Air Conditioning and Heating Refrigerant Compressor Oil - Check
C4.4 Industrial Engine Overspeed
C11 and C13 Engines for Caterpillar Built Machines Alternator - Remove and Install
C11 and C13 Engines for Caterpillar Built Machines Electric Starting Motor - Remove and Install
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers Factory Passwords
3412E Petroleum Engine CID 1835 FMI 03 Auxiliary Pressure Sensor open/short to +batt