Engine Oil Pump - Assemble
Show/hide table
需要的工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 1P-0510 | 驱动器总成 | 1 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 对齐发动机机油泵机体中的轴承 (11)。 让轴承接头与轴承孔中心线成45 ± 15度角。
- 使用工具 (A)并安装轴承 (11)。 轴承必须在齿轮孔
1.5 ± 0.5 mm (0.06 ± 0.02英寸) 以下。安装后测量轴承内径。 安装后轴承内径必须为
31.811 ± 0.013 mm (1.2524 ± 0.0005英寸) 。 如有必要,对轴承进行机加工。Show/hide table图 2 g00591963 - 在机体内 (9)安装轴组件 (10)。
Show/hide table
图 3 g01057514 - 确保定位销 (12)安装在盖组件 (7)上,与盖表面的距离保持在
6.0 ± 0.5 mm (0.24 ± 0.02 英寸) 。 - 使用工具 (A)在盖 (7)中安装轴承 (8),轴承接头对准正确的方向。
Show/hide table
图 4 g00591936 - 将盖 (7)就位并安装螺栓。
Show/hide table
图 5 g00591932 - 确保盖组件 (6)上的两个销安装在距盖表面
6.0 ± 1.0 mm (0.24 ± 0.04 英寸) 的位置上。 安装盖组件 (6)。Show/hide table图 6 g01005318 Show/hide table弹簧压缩零件如果安装不当,会伤害人体。
为避免伤害,遵照出版的装配程序,并穿上保护装备。
- 将清洁的发动机机油涂在阀槽 (5)上。 安装阀槽 (5)、弹簧 (4)、密封垫 (3)、盖 (2)和螺栓。
Show/hide table
图 7 g01005273 - 安装密封垫和接头 (1)。
注: 参考技术规范, "发动机机油泵"了解更多信息。
Show/hide table
图 1 | g01057511 |
结束:
- 安装发动机机油泵。 参考拆解与组装, "发动机机油泵 - 安装"。
Caterpillar Information System:
3064 and 3066 Engines for Caterpillar Built Machines Inlet Manifold - Install
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Alternator and Regulator
994D Wheel Loader Engine Supplement Radiator Guard, Radiator, and Oil Coolers - Install
994D Wheel Loader Engine Supplement Radiator Guard, Radiator, and Oil Coolers - Remove
3500B Engines Engine Oil Pump - Disassemble
515 and 525 Wheel SkiddersMachine Systems Steering Wheel - Remove and Install
545 Wheel Skidder Machine Systems Piston Pump (Implement, Pilot, Steering, Brake) - Install
545 Wheel Skidder Machine Systems Piston Pump (Implement, Pilot, Steering, Brake) - Remove
515 and 525 Wheel SkiddersMachine Systems Winch Input Gear (Pinion) - Install - C-500 Series Winch
3500B Engines Engine Oil Pump - Remove
545 Wheel Skidder Machine Systems Control Valve (Winch) - Install
Underground Mine Conversion for 980G Wheel Loader{7000} Underground Mine Conversion for 980G Wheel Loader{7000}
3500B Engines Engine Oil Pump - Install
3064 and 3066 Engines for Caterpillar Built Machines Cylinder Liner - Remove
3500B Engines Engine Oil Filter Housing - Remove
613C Series II Wheel Tractor-Scraper Hydraulic Tank Breaker Relief Valve - Clean
613C Series II Wheel Tractor-Scraper Refrigerant Dryer - Replace
613C Series II Wheel Tractor-Scraper Suction Screen (Transmission Scavenge) - Clean
613C Series II Wheel Tractor-Scraper Air System and Brakes Parking Brake - Test and Adjust
3500B Engines Engine Oil Filter Housing - Install
3500B Engines Engine Oil Filter Base - Remove - Spin-on Filters
545 Wheel Skidder Machine Systems Steering Cylinder - Remove and Install
613C Series II Wheel Tractor-Scraper Transmission Breather - Clean
3500B Engines Engine Oil Filter Base - Disassemble - Spin-on Filters