Input Drive Shaft - Remove and Install
Removal Procedure
Start By:
- Install the wheel chocks. Refer to Disassembly and Assembly, "Wheel Chock (Front and Rear) - Remove and Install".
- Connect the frame lock link. Refer to Disassembly and Assembly, "Frame Lock Link - Separate and Connect".
- Remove three bolts (1) that secure input drive shaft (2) to the torque converter. Discard three bolts (1). Do not reuse bolts.
Show/hide table
Illustration 1 | g00584219 |
- Remove three bolts (3) that secure input drive shaft (2) to the transfer gear case. Discard three bolts (3). Do not reuse bolts.
Show/hide table
Illustration 2 | g00584220 |
- Attach a suitable lifting sling around input drive shaft (2). Secure the suitable lifting sling to a hoist. Remove bolt (4) and bolt (5) from each end of input drive shaft (2). Discard bolt (4) and bolt (5). Do not reuse bolts.
Show/hide table
Illustration 3 | g00584221 |
- Use a prybar in order to compress input drive shaft (2) .
- Remove input drive shaft (2) from the yokes on the transfer gear case and the torque converter. The weight of input drive shaft (2) is 98 kg (215 lb).
- Remove four bolts (6) that secure spider (7) to input drive shaft (2). Discard four bolts (6). Do not reuse bolts. Remove spider (7) from input drive shaft (2). Repeat the procedure for the other end of input drive shaft (2) .
Show/hide table
Illustration 4 | g00584222 |
Installation Procedure
Note: Verify that all of the components of the input drive shaft are clean and free of foreign material prior to installation.
- Position spider (7) to input drive shaft (2). Install four new bolts (6) that secure spider (7) to input drive shaft (2). Tighten four bolts (6) to a torque of 530 ± 70 N·m (391 ± 52 lb ft). Repeat the procedure for the other end of input drive shaft (2) .
Show/hide table
Illustration 5 | g00584222 |
- Attach a suitable lifting sling around input drive shaft (2). Secure the suitable lifting sling to a hoist. Position input drive shaft (2) between the yokes on the transfer gear case and the torque converter. Align the input drive shaft in order to install two new bolts (4) and (5) to the yokes. Do not reuse bolts.
Show/hide table
Illustration 6 | g00584221 |
- Install three new bolts (3) that secure input drive shaft (2) to the transfer gear case. Do not reuse bolts. Tighten three bolts (3) and bolt (5) to a torque of 530 ± 70 N·m (391 ± 52 lb ft).
Show/hide table
Illustration 7 | g00584220 |
- Install three new bolts (1) that secure input drive shaft (2) to the torque converter. Do not reuse bolts. Tighten three bolts (1) and bolt (4) to a torque of 530 ± 70 N·m (391 ± 52 lb ft).
Show/hide table
Illustration 8 | g00584219 |
End By:
- Separate the frame lock link. Refer to Disassembly and Assembly, "Frame Lock Link - Separate and Connect".
- Remove the wheel chocks. Refer to Disassembly and Assembly, "Wheel Chock (Front and Rear) - Remove and Install".
Caterpillar Information System:
988G Wheel Loader Axle Oil Cooler Filter - Replace
D7R Series II Track-Type Tractor Power Train Pressure Charts
3034 Engine for Caterpillar Built Machines Flywheel - Install
994D Wheel Loader Power Train Gear Pump (Power Train) - Install
994D Wheel Loader Power Train Gear Pump (Power Train) - Remove
994D Wheel Loader Power Train Electronic Control Module (Power Train) - Remove and Install
3034 Engine for Caterpillar Built Machines Flywheel - Remove
994D Wheel Loader Power Train Drive Shaft (Rear) - Remove and Install
3408E and 3412E Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install
D6R Series II Track-Type Tractor Hydraulic System Ripper Lift Control Valve
3176C and 3196 Engines for Caterpillar Built Machines Aftercooler - Test
3408E and 3412E Engines for Caterpillar Built Machines Exhaust Temperature - Test
D6R Series II Track-Type Tractor Power Train Pressure Taps
D11R Track-Type Tractor Cooling System Coolant Extender (ELC) - Add
D11R Track-Type Tractor Cooling System Coolant (ELC) - Change
D11R Track-Type Tractor Engine Air Filter Primary Element - Replace
D10R Track-Type Tractor Engine Air Filter Primary Element - Replace
D7R Series II Track-Type Tractor Power Train Main Relief Valve - Adjust
D7R Series II Track-Type Tractor Power Train Priority Valve - Adjust
3034 Engine for Caterpillar Built Machines Flywheel Housing - Remove and Install
994D Wheel Loader Power Train Pump Drive (Rear) - Remove
994D Wheel Loader Power Train Pump Drive (Rear) - Install
615C Series II Wheel Tractor-Scraper Loading
584 and 584HD Forwarders Work Tools