Fuses and Circuit Breaker - Replace/Reset
Show/hide table
| Fuses - Fuses protect the electrical system from damage that is caused by overloaded electrical circuits. Replace a fuse if the element separates. If the fuse of a particular electrical system requires frequent replacement, check the electrical circuit. Repair the electrical circuit, if necessary. The fuse panel is positioned in the operator's compartment behind the access cover. This access cover is under the left side of the dashboard. |
Show/hide table
| NOTICE |
|---|
Always replace fuses with the same type and capacity fuse that was removed. Otherwise, electrical damage could result. |
Show/hide table
| NOTICE |
|---|
If it is necessary to replace fuses frequently, an electrical problem may exist. Contact your Caterpillar dealer. |
Show/hide table
 | |
| Illustration 1 | g00039297 |
Show/hide table
|
| Dump Valves (1) - 10 Amp |
Show/hide table
|
| Auxiliary Circuit (2) - 10 Amp |
Show/hide table
| Rear Floodlights (3) - 20 Amp |
Show/hide table
| Side Floodlights (4) - 20 Amp |
Show/hide table
| Seat Adjustment (5) - 10 Amp |
Show/hide table
| Heated Seat (6) - 10 Amp |
Show/hide table
| Console (7) - 10 Amp |
Show/hide table
| Windshield Wiper/Washer (8) - 15 Amp |
Show/hide table
| Horn (9) - 10 Amp |
Show/hide table
| Monitoring System (10) - 10 Amp |
Show/hide table
 | |
| Illustration 2 | g00039333 |
Show/hide table
| Circuit Breaker Reset - Push the button inward in order to reset the circuit breakers. If the circuit breaker reset is working properly, the button will stay depressed. If the button does not stay depressed, check the appropriate electrical circuit. |
Circuit breakers are in the operator compartment. These circuit breakers are behind the cover under the left side of the dashboard.
Show/hide table
| Power Outlet (1) - 15 Amp |
Show/hide table
| Fan Motor (2) - 15 Amp |
Show/hide table
| Electronic Clutch/Brake Control Lever (3) - 10 Amp |
Show/hide table
| Engine (4) - 15 Amp |
Show/hide table
| Engine Start Switch (5) - 15 Amp |
Show/hide table
| Main Circuit Breaker (6) - 105 Amp |
Show/hide table
| Alternator (7) - 105 Amp |
Caterpillar Information System:
D6R Series II Track-Type Tractor Hydraulic System Hydraulic Pump - Piston
613C Series II Wheel Tractor-Scraper Changing Direction and Speed
D10R Track-Type Tractor Fuses and Circuit Breakers - Replace/Reset
D11R Track-Type Tractor Indicators and Gauges - Test
3408E and 3412E Engines for Caterpillar Built Machines Flywheel - Install
D10R Track-Type Tractor Indicators and Gauges - Test
3034 Engine for Caterpillar Built Machines Exhaust Manifold - Remove and Install
963C Track-Type Loader Power Train Pump Drive - Install
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Flywheel - Remove
854G Wheel Dozer Seat
3408E and 3412E Engines for Caterpillar Built Machines Flywheel - Remove
611 Wheel Tractor-Scraper Wheel Tractor-Scraper Power Train Wheel Bearings - Adjust
D7R Series II Track-Type Tractor Hydraulic System Ripper Tip Control Valve
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Fuel Filter Lines
D7R Series II Track-Type Tractor Power Train References
613C Series II Wheel Tractor-Scraper Braking Operation
994D Wheel Loader Power Train Drive Shaft (Center) - Remove and Install
3408E and 3412E Engines for Caterpillar Built Machines Exhaust Temperature - Test
3176C and 3196 Engines for Caterpillar Built Machines Aftercooler - Test
D6R Series II Track-Type Tractor Hydraulic System Ripper Lift Control Valve
3408E and 3412E Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install
994D Wheel Loader Power Train Drive Shaft (Rear) - Remove and Install
3034 Engine for Caterpillar Built Machines Flywheel - Remove
994D Wheel Loader Power Train Electronic Control Module (Power Train) - Remove and Install