Starting Above 0°C (32°F)
Show/hide table
 | |
| Illustration 1 | g00100348 |
- Move the transmission direction control lever to the NEUTRAL position.
- Use the engine start switch key (1) in order to unlock the parking brake. The parking brake switch (2) must be ENGAGED.
Show/hide table
 | |
| Illustration 2 | g00100349 |
- Move the attachment control levers to the HOLD position.
Show/hide table
 | |
| Illustration 3 | g00649771 |
- Turn the battery disconnect switch to the ON position. The battery disconnect switch is inside of the access door on the left side of the machine.
Show/hide table
 | |
| Illustration 4 | g00100107 |
- Return the governor control lever to the LOW IDLE position.
Show/hide table
 | |
| Illustration 5 | g00101491 |
- Turn the key start switch to the ON position. The system performs an automatic self test. When you turn on the start switch key the test is performed. If the test is complete without any faults, proceed to next step. If the system detects a fault, check the electrical system. Make all of the necessary repairs before you start the engine.
Show/hide table
 | |
| Illustration 6 | g00101493 |
- The engine oil pressure light should turn on, and the alternator indicator light should turn on.
Show/hide table
 | |
| Illustration 7 | g00101495 |
- If the ambient temperature is below 10°C (50°F), push in the button for the air inlet heater. Prior to the start-up of the engine, the indicator for the air inlet heater will come on during the heating cycle.
Note: If the ambient temperature is above 10°C (50°F), you do not need to use the air inlet heater. The indicator does not need to go off in order to start the engine.
Show/hide table
 | |
| Illustration 8 | g00101501 |
- When the indicator for the air inlet heater goes off, turn the start switch key to the START position. Crank the engine. Release the key when the engine starts.
Show/hide table
 | |
| Illustration 9 | g00101496 |
Show/hide table
| NOTICE |
|---|
Do not crank the engine for more than 30 seconds. Allow the starter to cool for two minutes before cranking again. Turbocharger damage can result if the engine rpm is not kept low until the oil gauge display verifies that the oil pressure is sufficient. |
Caterpillar Information System:
992G Wheel Loader and 854G Wheel Dozer Braking System Limit Switch (Stop Light)
992G Wheel Loader and 854G Wheel Dozer Braking System Brake Control Valve (Parking)
992G Wheel Loader and 854G Wheel Dozer Braking System Parking Brake
D6M Track-Type Tractor Bulldozer Blade Lift Control
992G Wheel Loader and 854G Wheel Dozer Braking System Service Brakes
992G Wheel Loader Capacities (Refill)
561M Pipelayer Torque Converter and Pump Drive Housing
D5M Track-Type Tractor Transmission Control
992G Wheel Loader and 854G Wheel Dozer Braking System Limit Switch (Parking Brake)
D6R Track-Type Tractor Finger Tip Control (FTC)
561M Pipelayer Torque Converter
D5M Track-Type Tractor Governor and Decelerator
D5M Track-Type Tractor Power Train Transmission and Torque Converter Pump
561M Pipelayer Engine Starting with Jump Start Cables
D6M Track-Type Tractor Starting Below 0°C (32°F)
D5M Track-Type Tractor After Starting Engine
D5M Track-Type Tractor Changing Direction and Speed
D6R Track-Type Tractor Normal Steering
631E Series II Wheel Tractor-Scrapers Crushing Prevention and Cutting Prevention
D6R Track-Type Tractor Steering on a Steep Downgrade
631E Series II Wheel Tractor-Scrapers Sound Information and Vibration Information
D6R Track-Type Tractor Stopping the Machine
D6M Track-Type Tractor Lifting and Tying Down the Machine
D5M Track-Type Tractor Towing the Machine