651E Wheel Tractor-Scraper Caterpillar


Safety Signs and Labels

Usage:

651E 4YR
There are several specific warning signs on this machine. The exact location of the hazards and the description of the hazards are reviewed in this section. Please become familiarized with all warning signs.

Make sure that all of the warning signs are legible. Clean the warning signs or replace the warning signs if you cannot read the words. Replace the illustrations if the illustrations are not legible. When you clean the warning signs, use a cloth, water and soap. Do not use solvent, gasoline, or other harsh chemicals to clean the safety signs. Solvents, gasoline, or harsh chemicals could loosen the adhesive that secures the warning sign. Loose adhesive will allow the warning sign to fall.

Replace any safety sign that is damaged, or missing. If a safety sign is attached to a part that is replaced, install a safety sign on the replacement part. Any Caterpillar dealer can provide new safety signs.

Do Not Operate




Illustration 2g00100497

This warning label is positioned in the cab.



g00038370

------ WARNING! ------

DO NOT OPERATE OR WORK ON THIS MACHINE UNLESS YOU HAVE READ AND UNDERSTAND THE INSTRUCTIONS AND WARNINGS IN THE OPERATION AND MAINTENANCE MANUALS. FAILURE TO FOLLOW THE INSTRUCTIONS OR HEED THE WARNINGS COULD RESULT IN INJURY OR DEATH. CONTACT ANY CATERPILLAR DEALER FOR REPLACEMENT MANUALS. PROPER CARE IS YOUR RESPONSIBILITY.

----------------------

Do Not Weld The ROPS




Illustration 3g00100398

This warning label is positioned on the ROPS.



g00100417

------ WARNING! ------

Structural damage, an overturn, modification, alteration, or improper repair can impair this structure's protection capability thereby voiding this certification. Do not weld on or drill holes in the structure. Consult a Caterpillar dealer to determine this structure's limitations without voiding its certification.

----------------------

High Compressed Spring




Illustration 4g00100400

This warning label is positioned on the brake actuator.



g00100414

------ WARNING! ------

Highly compressed spring inside this housing can cause serious physical injury or death.

Do not service until you read and understand the information in the service manual when servicing the parking/secondary brake actuator.

----------------------

No Clearance




Illustration 5g00100404

This warning label is positioned on the hitch link.



g00100418

------ WARNING! ------

Hitch and steering movement can reduce clearances suddenly and cause personal injury...

Stop engine before servicing.

----------------------

Improper Connections For Jump Start Cables




Illustration 6g00100405

This warning label is positioned in the battery compartment.



g00038786

------ WARNING! ------

Improper jumper cable connections may cause an explosion resulting in personal injury. Batteries may be located in separate compartments. When using jumper cables, always connect positive (+) cable to positive (+) terminal of battery connected to starter solenoid and negative (-) cable from external source to starter negative (-) terminal. (If not equipped with starter negative terminal, connect to engine block.) Follow procedure in the Operation and Maintenance Manual.

----------------------

High Pressure Cylinder




Illustration 7g00100408

This warning label is positioned on all accumulator cylinders.



g00100419

------ WARNING! ------

High pressure cylinder:

Do not remove any valve, hydraulic fitting, or valve core, nor disassemble any parts until pressure has been relieved or personal injury may occur.

To relieve pressure:

1. Shut off engine and wait five minutes for hydraulic system pressure to dissipate.

2. Relieve gas pressure in the accumulator cylinder by opening the charging valve one turn only.

See your Caterpillar dealer for tools and detailed information required for charging cylinders.

Charge cylinder with dry nitrogen gas.

----------------------

Block The Apron




Illustration 8g00100413

This warning label is positioned on the side of the bowl.



g00100420

------ WARNING! ------

BLOCK THE APRON UP WHEN MAINTENANCE REQUIRES THE APRON TO BE OPEN.

Apron movement can cause serious injury unless these steps are taken.

  1. Place the apron in the up position.

  1. Stop the engine.

  1. Move the disconnect switch to off and remove the key.

  1. Place a Do Not Operate tag on the steering wheel.

  1. Remove the retaining bolt (A).

  1. Remove the pin (B). Storage opposite end some models.

  1. Install the pin (B) in position (C).

  1. Install the retaining bolt (A).

  1. Lower the apron on to the pin (B).
----------------------

Shipping Brackets




Illustration 9g00100421

This warning label is positioned on right and left side of the scraper.



g00100422

------ WARNING! ------

SHIPPING BRACKETS ARE DESIGNED TO PERMIT MACHINE TRAVEL UNDER THE FOLLOWING CONDITIONS ONLY.

  1. No load in the bowl.

  1. Run rear engine if so equipped, with transmission in NEUTRAL.

  1. Travel in FIRST speed only.

  1. Travel distance limited to 5 miles.

  1. Apron control lever must be in FLOAT position.

Improper machine usage can cause travel brackets to fail and result in personal injury or machine damage.

----------------------
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.