Piston and Connecting Rods - Remove
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
A     | 9S-9082     | 发动机盘车工具     | 1     |
B     | 1P-1861     | 挡圈钳     | 1     |
C     | 6V-4020     | 活塞环扩展器     | 1     |
D     | 5P-8639     | 液压压力     | 1     |
5P-9725 | 液压油缸     | 1     | |
8F-0024 | 软管组件     | 1     | |
1P-2375 | 连接器     | 1     | |
1P-2376 | 连接器     | 1     | |
1U-5230 | 手动液压泵     | 1     | |
5P-8640 | 条形卡箍     | 1     | |
E     | 6V-3042     | 适配器     | 1     |
F     | 6V-3043     | 隔套     | 1     |
G     | 5P-8649     | 适配器     | 1     |
开始:
- 拆卸缸盖。 请参阅拆解和组装, "缸盖 - 拆卸"。
- 卸下活塞冷却喷嘴。 请参阅拆解和组装, "活塞冷却喷嘴 - 拆卸和安装"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 使用工具 (A) 转动发动机以接近连杆盖上的螺栓。
- 在每个连杆和相应的连杆盖上标记汽缸号。
注: 发动机的前端与飞轮端相对。 1 1 汽缸位于右侧发动机的前端。 1 2 汽缸位于左侧。
- 从连杆上拆卸螺栓 (1) 和连杆盖 (2) 。
Show/hide table
图 1 | g00582418 |
- 将轴承从连杆 (2) 和连杆盖上拆下。
- 将活塞 (3) 从缸套内推出,直到活塞环从缸套中完全脱出。
Show/hide table
图 2 | g00582419 |
- 拆卸活塞和连杆组件。
- 使用工具 (B) 拆下固定活塞销 (4) 的挡圈。
Show/hide table
图 3 | g01051820 |
- 拆卸活塞销 (4) 。
- 从连杆 (5) 上拆卸活塞 (3) 。
- 使用工具 (C) 从活塞 (3) 上拆卸活塞环 (6) 。
Show/hide table
图 4 | g00582421 |
- 用合适的环形凹槽工具清洁活塞环形凹槽。 有关清洁活塞的正确步骤,请参考再使用零件指南, SEBF8059, "清洁和检查 3500 系列发动机活塞的步骤"。
- 提高连杆温度。
注: 不要直接使用火焰来加热连杆。
- 将工具 (F) 放在工具 (D) 的底座上。 在底座上安装连杆。
Show/hide table
图 5 | g01089121 |
- 将活塞销轴承对准工具 (D) 上的端口组件中心。 在活塞销孔的中心安装销 (9) 。
- 安装工具 (G) 。 将适配器中的孔与工具 (D) 底座的孔对齐。
- 安装条形卡箍和卡箍销 (10) 。
注: 安装新轴承时将旧轴承往外推。
- 固定工具 (E) 让锥形侧倒置。 活塞销轴承接头必须与适配器和工具 (D) 底座中的孔对齐。
- 将拉拨器 (7) 置于适配器 (11) 上。
- 使用工具 (D) 将新活塞销轴承 (8) 推入连杆,直到适配器 (11) 与连杆接触。
- 从工具 (D) 上拆卸连杆和旧活塞销轴承。
- 安装活塞销轴承后,测量轴承孔径。 正确直径应为 70.000 ± 0.008 mm (2.7559 ± 0.0003 in)。
- 请参考专门说明书, SEHS7295, "活塞销轴承拆卸和安装工具的使用",了解更多信息。
Caterpillar Information System:
G3304 and G3306 Engines Crankshaft - Install
3500 Engines Fuel Filter Housing - Install
3500 Engines Fuel Filter Housing - Remove
G3304 and G3306 Engines Crankshaft - Remove
3406C Marine Auxiliary Generator Set Plate Locations and Film Locations
G3304 and G3306 Engines Camshaft Bearings - Install
G3304 and G3306 Engines Camshaft Bearings - Remove
C11, C13 and C15 On-highway Engines 0105-04 Intake Manifold Air Temperature voltage low (38)
C11, C13 and C15 On-highway Engines 0105-03 Intake Manifold Air Temperature voltage high (38)
Bench Test Procedure for Hydraulic Piston Pumps{5070} Bench Test Procedure for Hydraulic Piston Pumps{5070}
G3500 Engines MID 018 - CID 0523 - FMI 11 No A/F Ratio Engine Speed Sensor **Shutdown**
G3304 and G3306 Engines Cylinder Liner - Install
G3520C and G3520E Generator Set Engines Piston and Connecting Rods - Install
2003/06/01 Improved Radiator for the Generator Set Engine {1353}
G3500 Engines MID 018 - CID 0551 - FMI 01 Oxygen Sensor not connected to buffer
G3500 Engines MID 018 - CID 0552 - FMI 11 Engine Speed present during an O2 calibration
3044C Industrial Engine and Engines for Caterpillar Built Machines Engine Oil Bypass Valve - Remove and Install
UPS 250, UPS 300, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supply Flywheel Telemetry - Calibrate
G3520C and G3520E Generator Set Engines Cylinder Liner - Install
3508C, 3512C and 3516C Marine Engines Camshaft Bearings - Remove
Replacing the Convection Jacket Water Heaters with a Recirculating Jacket Water Heater on 3500 Engines{1383} Replacing the Convection Jacket Water Heaters with a Recirculating Jacket Water Heater on 3500 Engines{1383}
3508C, 3512C and 3516C Marine Engines Camshaft Bearings - Install
C3.3 Industrial Engine Engine - Clean
2003/07/01 An Improved Spin-On Oil Filter Is Now Available {1306, 1308}