Engine Oil Pump - Disassemble
Show/hide table
Required Tools | |||
Tooling | Part Number | Description | Qty |
A | 1P-2320 | Combination Puller | 1 |
8B-7560 | Step Plate | 1 | |
B | 1P-0529 | Handle | 1 |
1P-0468 | Drive Plate | 1 | |
1P-0465 | Drive Plate | 1 | |
C | 1P-0462 | Drive Plate | 1 |
1P-0461 | Drive Plate | 1 | |
1P-0529 | Handle | 1 |
Start By:
- Remove the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Remove" for the engine that is being serviced.
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Remove idler gear (2).
- Use Tooling (B) in order to remove the bearing from idler gear (2).
- Remove suction bell (1).
Show/hide table
Illustration 2 g00989781 - Remove the bolt and the washer from drive gear (4).
- Use Tooling (A) in order to remove drive gear (4) from the shaft.
- Remove the key from the shaft.
- Remove two bolts (3) from the pump body.
Show/hide table
Illustration 3 g00989782 - Remove pump body (9), two gears (8), the keys, and spacer (5) from the pump.
- Remove two shafts (6) and the gears.
- Remove bolt (7), the cover, and the pressure relief valve from the body.
Show/hide table
Illustration 4 g00989783 - Use Tooling (C) in order to remove the bearings from the oil pump body assembly and the scavenge pump body assembly.
Show/hide table
Illustration 1 | g00989769 |
Show/hide table
Illustration 5 | g00989784 |
Reference Photo |
Caterpillar Information System:
C7 Engines for Combat and Tactical Vehicles Data Link Parameters
G3304 and G3306 Engines Engine Oil Pump - Install
3516B HD Generator Set Engine Mounts - Check
3126E and 3126B Commercial and Truck Engines Federal Emission Control Warranty
C7 Engines for Caterpillar Built Machines Camshaft Idler Gear - Remove and Install
C15 and C18 Generator Set Engines Pistons and Connecting Rods - Install
C15 On-highway Engine Pistons and Connecting Rods - Remove
C15 and C18 Generator Set Engines Connecting Rod Bearings - Remove
C15 On-Highway Engine Crankshaft - Install
C15 and C18 Generator Set Engines Pistons and Connecting Rods - Disassemble
C15 On-Highway Engine Pistons and Connecting Rods - Assemble
C15 On-Highway Engine Camshaft - Remove
C7 Engines for Combat and Tactical Vehicles Dedicated PTO Parameters
C7 Engines for Combat and Tactical Vehicles Engine/Gear Parameters
3126E and 3126B Commercial and Truck Engines California Emission Control Warranty Statement
C7 Engines for Combat and Tactical Vehicles Engine Monitoring Parameters
C15 On-highway Engine Engine Oil Cooler - Remove
3500B Series II Marine Engines MID 036 - CID 0253 - FMI 02 Personality Module mismatch
3500B Series II Marine Engines MID 036 - CID 0254 - FMI 12 Electronic Control Module Error
3516B HD Generator Set Generator Oil Level - Check
3500B Generator Sets Safety Messages
C15 On-highway Engine Engine Oil Cooler - Install
C7 and C9 On-Highway Engines Diagnostic Codes
C7 Engines for Caterpillar Built Machines Camshaft Bearings - Remove and Install