Crankshaft
Show/hide table
Illustration 1 | g00987940 |
(1) Crankshaft end play
- Standard at assembly ... 0.100 to 0.264 mm (0.0039 to 0.0104 inch)
- Repair limit ... 0.300 mm (0.0118 inch)
Crankshaft deflection
- Maximum at assembly ... 0.02 mm (0.0008 inch)
- Repair limit ... 0.05 mm (0.0020 inch)
Clearance between crankshaft bearing and crankshaft journal
- Standard at assembly ... 0.050 to 0.110 mm (0.0020 to 0.0043 inch)
- Repair limit ... 0.200 mm (0.0079 inch)
Show/hide table
Illustration 2 | g00994009 |
(A) Original width of the rear crankshaft journal ... 31.000 to 31.039 mm (1.2205 to 1.2220 inch)
Show/hide table
Width of Crankshaft Journal for Oversize Thrust Washers     | ||
Oversize Thrust Washer     | Oversize Width for Front OR Rear     | Oversize Width for Front AND Rear     |
0.15 mm (0.006 inch)     |
31.150 to 31.189 mm (1.2264 to 1.2279 inch)     |
31.300 to 31.339 mm (1.2323 to 1.2338 inch)     |
0.30 mm (0.012 inch)     |
31.300 to 31.339 mm (1.2323 to 1.2338 inch)     |
31.450 to 31.489 mm (1.2382 to 1.2397 inch)     |
0.45 mm (0.018 inch)     |
31.450 to 31.489 mm (1.2382 to 1.2397 inch)     |
31.600 to 31.639 mm (1.2441 to 1.2456 inch)     |
Refer to Specifications, "Connecting Rod Bearing Journal" for information on the connecting rod bearing journals.
Refer to Specifications, "Main Bearing Journal" for information on the main bearing journals and the main bearings.
Caterpillar Information System:
G3500 Engines Prelube Pump - Air
3046 Engine for Caterpillar Built Machines Connecting Rod - Inspect
3044C Industrial Engine and Engines for Caterpillar Built Machines Cylinder Head - Inspect
R1600H Load Haul Dump Turbocharger - Inspect
3044C Industrial Engine and Engines for Caterpillar Built Machines Gear Group - Inspect
G3500B Engines Air Starting Motor - Turbine
3046 Engine for Caterpillar Built Machines Flywheel - Inspect
C11, C13, and C15 On-highway Engines Compression Brake - If Equipped
G3520C and G3520E Generator Set Engines Rocker Shaft - Assemble
G3520C and G3520E Generator Set Engines Rocker Shaft - Disassemble
C4.4 Industrial Engine Engine Oil Pump - Inspect
3044C Industrial Engine and Engines for Caterpillar Built Machines Cylinder Block
G3500B Engines Prelube Pump - Air
3044C Industrial Engine Starting the Engine
G3500B Engines Prelube Pump - Electric
G3516B Engines Replacing the ITSM
3034 Engine for Caterpillar Built Machines Crankshaft - Remove
UPS 250, UPS 300, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supply EMI Filter Board - Remove and Install
Cat Gas Engine Lubricant, Fuel, and Coolant Recommendations Aftermarket Oil Additives
G3500 Engines Prelube Pump
Cat Gas Engine Lubricant, Fuel, and Coolant Recommendations Dry Natural Gas - Pipeline
G3500 A3 Engines Prelube Pump - Electric
C11, C13 and C15 On-highway Engines ATA (SAE J1587 / J1708) Data Link Circuit - Test
G3500B Engines Exhaust Manifold