1978/02/13 Caterpillar


Several Improvements Made To Lines Group In Area Of The Hitch{5057,5077}

Usage:


641B, 651B and 657B Tractors

Reference: Reference Articles in Service Magazines:

... "New Cushion Hitch Hose and Clamps, and Reinforcement for Hose Guides" July 31, 1973, Pages 10 and 11.

... "New Hose Assembly Used in Accumulator Lines for Cushion Hitch" October 11, 1974, Page 11.

... "Hitch Lines Improvements; Including Hoses, Supports and Mounting Clamp" June 19, 1975 Pages 9 and 10.

Reference: The reference articles listed above are about changes which have been made before in this same area. Before making any changes on earlier machines in the field, check to determine what changes have been made to your machine.

Description of Change: Several improvements have been made to the lines group in the area of the hitch.

... A 3G5303 Plate has also been installed above the hitch pivot pin to keep the accumulator hose assembly away from the bolts.

A new 3G5304 Hose Assembly is used as a replacement for the 9J7552 Hose Assembly in the 6J6664 Accumulator Lines Group. The new hose assembly has two of the eight sleeves moved farther away from the 90° stem assembly.

... New clamps and hose assemblies are used on the 7D160 and 7D1570 Hitch Lines Group (641B, 651B and 657B respectively). The clamps are of a new design to prevent external damage to the hose assemblies. Also, a plate with a "U" shape is used on the end of the hitch lines clamp to prevent wear to the accumulator hose by the side plates of the clamp.

The hose assemblies are a little shorter to give more resistance to movement which causes wear.

INSTALLATION:

... Remove the 9J7552 Accumulator Hose Assembly. See Illustration 1 and install the channel and the plate. Install the 3G5568 Clamp and the new 3G5304 Accumulator Hose Assembly as shown in Illustration 2.


Illustration 1. Location of channel and plate.


Illustration 2. Location of 3G5304 Hose Assembly and 3G5568 Clamps.

... Install the other parts. Illustration 3 shows the 7D1570 Hitch Lines Group used on the 657B. The 7D160 Hitch Lines Group is similar, but, the retarder air line, multi-conductor cables, and battery cables are not part of the hitch lines group.


Illustration 3. Illustration shown is hitch line group for 657B. Hitch line group for 641B and 651B is similar.

Caterpillar Information System:

1978/02/13 Complete Set Of Contact Points For Dial Indicators Is Now Available In One Group{0653}
1978/02/13 Replacement Seal Group For Water Pump Impeller Now Has All The Seal Parts Plus An Installation Tool{1361,0622}
1978/02/06 Probable Causes Of Low Fuel Delivery During Testing On Fuel Injection Test Benches{0650,1250}
1978/02/06 New Water Temperature Regulator Opens At 180°F (82°C){1350,1355,7304}
1978/02/06 Successful Engine Service-3208 Engine Booklet Is Available{1000}
1978/02/06 Stronger Clutch Housing Used In Variable Capacity Torque Converter{3102}
1978/02/06 Add New Measurement And Identification To FT904 Backlash Indicator{0653,3258}
1978/02/06 Adjustment Of Track Tension On Machines With One Carrier Roller Per Side{4150}
1978/02/06 Silicone Sealant Is Now Used To Keep Water Out Of The Steering Clutch Case{4059,4100,4106,4115}
1978/01/30 Air Line For Air Compressor Governor Now Connected To Outlet For Wet Air Tank{4272,1065,4278}
1978/01/30 Retaining Ring Of A New Design Now Used In Torque Converter Group{3100}
1978/01/30 Do Not Change Factory Fuel Or Speed Settings On Truck Engines Unless New Settings Are Certified Under Applicable EPA Regulations{0336,0337,1257}
1978/02/13 Improvements Made To Push Frame; Instructions To Make Reinforcements On Earlier Push Frames Available{6225}
1978/02/13 Strip Added Under The Hinge For The Front Windshield On ROPS Cabs{7325}
1978/02/13 Check Degree Number On Timing Fixture Plate Assemblies{0650}
1978/02/20 New Transmission Valve Groups Increase Winch Line Pull When Transmission Is In Neutral{3150,3152,3157,3167,3100}
1978/02/20 Separate Parts Of Tire Valve Group Now Available For Parts Service{4202}
1978/02/20 Reinforcements For Front Frame{7051}
1978/02/20 Improved Lift Arm And Service Brace Now Used{0643,5102,6119}
1978/02/20 Muffler Mounting Group Now Used To Give More Support To Muffler{1062}
1978/02/27 Use New Thickness Gauge To Check For Reusability Of Transmission Disc Assemblies Made From F37 Clutch Friction Material{0653,3155}
1978/02/27 New Hose Assembly Used In Oil Lines Group For Brake Cooling{3154,4100}
1978/02/27 New Oil Specifications For Gearmatic Winches{5163}
1978/02/27 New Seal Assembly With Longer Ferrule Prevents Damage To Ferrule During Cylinder Head Installation{1100,1101,1300}
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.