New Part Available To Check The 3S1467 Plunger And Barrel Assemblies{1251,1252,0652}
Usage:
D346, D348, D349 Engines
It is now possible to make a test of the 3S1467 Plunger and Barrel Assemblies of the above engines on the Caterpillar Fuel Injection Test Bench. A new 6V121 Fuel Injection Line is needed to make this test. The new line connects the injection pump to the master valve.
See Special Instruction Form No. SEHS7465, "Using The Caterpillar Fuel Injection Test Bench", for the correct test procedure and specifications to check the 3S1467 Plunger and Barrel Assemblies.
Caterpillar Information System:
1980/05/12 Boss Can Be Removed From Spacer Plate Cylinder Block To Get Clearance For Oil Filler Tube{1201,1316}
1980/05/12 "I checked everything but..."{0100}
1980/05/12 Improvements To Engine Oil Lines Group Makes Installation Easier; Prevents Reverse Connections{1307,1318,1155}
1980/05/12 Use The FT1525 Alignment Pin And FT1526 Fixture When Reconditioning Earlier 3208 Sleeve Metering Fuel Systems{0626,1264,1286}
1980/05/05 Hardened Washers Now Used On Bolts For Fan Shroud{1353,1360}
1980/05/05 Improvements Made To Water Separator Groups{1263}
1980/05/05 Changes To 9S240 Rack Position Tool Group; Revision To Special Instructions{0653,0374,1250}
1980/05/05 New 6V2120 Spline Sprocket Improves Depth Control Of 5P4175 Boring Tool Group{0663}
1980/04/28 Use 6V3044 Polishing Belt For Crankshaft Reconditioning{0622,1202}
1980/04/28 Boring Machine, Adapter Groups And Sleeves Available For Repair Of Damaged Cylinder Blocks{0622,1201,1216}
1980/04/28 New 1N3270 Auxiliary Drive Group Available As Attachment{1165}
1980/04/21 Crankcase Capacity Increased And New Oil Level Gauges Used; Specifications For Conversion Of Existing Gauges{1318,1302}
1980/05/12 Possible Cause Of A Low Idle Misfire And/Or Backfire{1278,1076,1250}
1980/05/12 Bushing Bores In Boom Can Be Machined In The Field{6501,0664}
1980/05/12 Changes To Oil Level Gauge Group Improve Accuracy Of Oil Level Indications, Increase Oil Capacity Of 245 Excavators And Front Shovels{1300}
1980/05/19 Important: 7V2253 Anti-Creep Slides Must Be Correctly Installed, And Adjusted With The Seat Belt{7327}
1980/05/19 Turbine Wheel Shroud Design Changed; Snap Ring No Longer Used{1052}
1980/05/19 "Viscor Cup" Available To Check SAE J967 Calibration Fluid For Fuel Injection Test Bench{0651}
1980/05/19 New Plug With Straight-Threads Used In Engine Variable Timing Drive{1272}
1980/05/26 6V97 Engine Stand Is Available{0626}
1980/05/26 New Check Valve Used In Fuel Injection Pump Assembly{1251}
1980/05/26 Four Fabricated Tools Available To Adjust Carrier Bearing Preload And Backlash (Tooth Clearance) For Bevel Gear And Pinion{0611,3258,3256,3257}
1980/05/26 6V6 Electrical Connector Pliers Available{0613}
1980/06/02 Improved Procedure Can Be Used To Adjust Voltage Gain{4467}