C12 Marine Engines Caterpillar

Magnetic Pickup

Usage:

C-12 9HP

Show/hide table




Illustration 1	g01418609

(A) Distance between end of magnetic pickup and ring gear ... 0.10 to 0.75 mm (0.004 to 0.030 inch)

To set the distance between the magnetic pickup and the ring gear, use the procedure that follows. The engine must be stopped.

Turn the magnetic pickup until the magnet is against the ring gear tooth.
1. To ensure that the magnetic pickup is against a tooth on the ring gear, look through the opening that is in the flywheel housing.
Back out the magnetic pickup by 120 ± 36 degrees.

(1) Torque for the nut ... 45 ± 7 N·m (33 ± 5 lb ft)

Caterpillar Information System:

2002/02/01 Introduction of a New Tappet Plug {1209}

2002/02/25 Introduction of a New Tappet Plug {1209}

C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers CID 0005 FMI 11 Cylinder #5 Injector fault

C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers CID 0004 FMI 11 Cylinder #4 Injector fault

C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers CID 0003 FMI 11 Cylinder #3 Injector fault

C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers CID 0002 FMI 11 Cylinder #2 Injector fault

C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers CID 0001 FMI 11 Cylinder #1 Injector fault

C12 Marine Engines Electric Starting Motor

3408E and 3412E Engines for Caterpillar Built Machines Electric Starting Motor

324D and 326D Excavators Machine System Specifications Track Roller Mounting

Procedure For Sealing Cracks In The Air Plenum That Are On The Top Surface Of The Cylinder Block{1201} Procedure For Sealing Cracks In The Air Plenum That Are On The Top Surface Of The Cylinder Block{1201}

CIPI UNDERCARRIAGE Arrangements: 9Q-5195, 9Q-5197, 9Q-5198, 9Q-5232, 9Q-5504, 9Q-5643, 9Q-5651, 9Q-5727, 9Q-5728, 9Q-5729, 9Q-5730, 9Q-5731, 9Q-5747, 9Q-5876, 180-4029, and 213-3892 Final Drive - Assemble

CIPI UNDERCARRIAGE Arrangements: 3Q6662, 6Z7861, 6Z7885, 6Z7947, 6Z7957, 6Z7999, 9Q5044, 9Q5065, 9Q5082, 9Q5090, 9Q5093, 9Q5115, 9Q5118, 9Q5126, 9Q5135, 9Q5141, 9Q5168, 9Q5175, 9Q5206, 9Q5255, 9Q5259, 9Q5268, 9Q5412, 9Q5436, 9Q5464, 9Q5514, 9Q5617, 9 Motor Control (Travel)

CIPI UNDERCARRIAGE Arrangements: 3Q6662, 6Z7861, 6Z7885, 6Z7947, 6Z7957, 6Z7999, 9Q5044, 9Q5065, 9Q5082, 9Q5090, 9Q5093, 9Q5115, 9Q5118, 9Q5126, 9Q5135, 9Q5141, 9Q5168, 9Q5175, 9Q5206, 9Q5255, 9Q5259, 9Q5268, 9Q5412, 9Q5436, 9Q5464, 9Q5514, 9Q5617, 9 Travel Motor

C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers CID 0164 FMI 02 Injector Actuation Pressure signal erratic

C12 Marine Engine Cooling System - Check - Overheating

C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers CID 0342 FMI 02 Loss of Secondary Engine Speed signal

CIPI UNDERCARRIAGE Arrangements: 3Q6662, 6Z7861, 6Z7885, 6Z7947, 6Z7957, 6Z7999, 9Q5044, 9Q5065, 9Q5082, 9Q5090, 9Q5093, 9Q5115, 9Q5118, 9Q5126, 9Q5135, 9Q5141, 9Q5168, 9Q5175, 9Q5206, 9Q5255, 9Q5259, 9Q5268, 9Q5412, 9Q5436, 9Q5464, 9Q5514, 9Q5617, 9 Travel Counterbalance Valve

G3612 and G3616 Engines Air Inlet Restriction Sensor - Remove and Install

C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers Engine Vibration

CIPI UNDERCARRIAGE Arrangements: 3Q6662, 6Z7861, 6Z7885, 6Z7947, 6Z7957, 6Z7999, 9Q5044, 9Q5065, 9Q5082, 9Q5090, 9Q5093, 9Q5115, 9Q5118, 9Q5126, 9Q5135, 9Q5141, 9Q5168, 9Q5175, 9Q5206, 9Q5255, 9Q5259, 9Q5268, 9Q5412, 9Q5436, 9Q5464, 9Q5514, 9Q5617, 9 Oil Makeup (Travel System)

2002/02/01 A New Tightening Procedure For Water Pump Bolts {1361}

N3 Series Brushless Alternators Alternator

C12 Marine Engine Cooling System - Inspect