Camshaft
Show/hide table
图 1 | g00295235 |
Show/hide table
图 2 | g00295231 |
(1) 垫圈
- 新垫圈的厚度 ... 8.50 ± 0.05 mm (0.335 ± 0.002 in)
- 新凸轮轴中凹槽的厚度 ... 8.75 ± 0.05 mm (0.344 ± 0.002 in)
- 新凸轮轴的端隙 ... 0.15 至 0.35 mm (0.006 至 0.014 in)
- 新凸轮轴中凹槽的厚度 ... 8.75 ± 0.05 mm (0.344 ± 0.002 in)
(2) 左凸轮轴
(3) 右凸轮轴
(4) 轴颈表面
- 新凸轮轴轴承表面(轴颈)的直径 ... 85.88 ± 0.02 mm (3.381 ± 0.001 in)
- 组装后的凸轮轴轴承孔孔径 ... 86.00 ± 0.06 mm (3.386 ± 0.002 in)
(5) 凸轮轴凸轮高度
请使用以下步骤来确定这一高度:
- 测量凸轮轴凸轮高度 (5) 。
- 测量基圆 (7) 。
- 用凸轮高度(步骤2 )减去基圆(步骤1 )。 二者之差即为实际凸轮升程。
- 规定的凸轮轴凸轮升程 (6)
进气凸轮 ... 9.314 mm (0.3667 in)
喷油器凸轮 ... 13.574 mm (0.5344 in)
排气凸轮 ... 9.078 mm (0.3574 in)
Caterpillar Information System:
SPT342 Truck Mounted Pumper Model View Illustrations
G3612 and G3616 Engines Crankshaft
Electronic Modular Control Panel II+ (EMCP II+) Reading DC Schematics
2001/06/01 Change to the Torque of the Adjusting Screw Locknut for the Unit Injector (Testing and Adjusting Manuals) {1290}
3034 Marine Engine Electric Starting System - Test
3034 Marine Engine - Installation Guide Exhaust System
SPT342 Truck Mounted Pumper Maintenance Interval Schedule
G3600 Engines BTU and Precombustion Chamber Adjustments
G3600 Engines General Information (Air Inlet and Exhaust System)
37-MT, 41-MT, and 42-MT Series Starting Motors Brush and Brush Holder - Check
3034 Marine Engine - Installation Guide Propeller Shaft and Coupling
G3600 Engines Procedure for Engine Timing
G3304 and G3306 Engines Exhaust Manifold
G3304 and G3306 Engines Engine Oil Pan
784C, 785C, 785D, 789C, 789D, 793C and 793D Off-Highway Trucks Power Train Electronic Control System MID 027 - CID 0168 - FMI 01
Wabco Air Compressors Specification
G3304 and G3306 Engines Crankcase Breather
G3304 and G3306 Engines Water Pump
Generator Set Start Module Safety Signs and Labels
3612 and 3616 Engines Crankshaft Seals
Generator Set Start Module General Hazard Information
37-MT, 41-MT, and 42-MT Series Starting Motors Starting Motor Does Not Turn or Turns Slowly
G3600 Engines Cylinder Block
G3304 and G3306 Engines Radiator