Front Idler
Show/hide table
| |
| Illustration 1 | g03427901 |
Show/hide table
| Specification for 248-7151 Front Idler Gp | |||
| Item | Qty | Part | Specification Description |
| 1 | 1 | 7H-3171 Pipe Plug | Remove the pipe plug from the front idler assembly and apply air pressure to this port. Front idler assembly should sustain |
| 2 | 2 | 109-0868 Duo-Cone Seal Gp | The rubber toric seals and all the contacting surfaces must be clean and dry at assembly. Prior to assembly, apply a thin film of 6V-4876 Lubricant to the contacting surfaces of the metal seal rings. The metal seal rings must be assembled square. The rubber toric seal should not bulge and the rubber toric seal should not twist.
|
| 3 | - | - | Before assembly, the surfaces must be clean and free from protective coating. |
| 4 | 1 | 124-9978 Idler Shaft | Install the idler shaft. Position the "R" that is stamped on the end face of the idler shaft backward into the front idler bearing. |
| C | - | - | Install the pin with the slit in the range that is specified. Refer to Illustration 1 for the correct position of the pin.
Specified range is 40 degrees. |
| D | - | - | Angle from centerline of idler shaft is 20 degrees. |
| - | - | - | End play in axial direction:
Minimum is Maximum is |
Caterpillar Information System:
326F, 329F and 330F Excavators Machine Systems Counterweight - Remove and Install
345D and 349D Excavators TA2 Technical Inspection{0372, 1000, 7000, 753T, 7565} 345D and 349D Excavators TA2 Technical Inspection{0372, 1000, 7000, 753T, 7565}
326F, 329F and 330F Excavators Machine Systems Cab - Remove and Install
311D, 312D, 312D2, 313D, 313D2, 314D, 315D, 318D, 318D2 and 319D Excavators Machine Electronic Control System MID 039 - CID 0100 - FMI 04
2013/09/18 Cable Straps are Now Used to Prevent Hose Interference and Extend the Service Life of Hydraulic Hoses on Certain Mini Hydraulic Excavators {5057}
311D, 312D, 312D2, 313D, 313D2, 314D, 315D, 318D, 318D2 and 319D Excavators Machine Electronic Control System MID 039 - CID 0100 - FMI 03
2013/09/19 An Improved Bulk Hose is Now Used for Certain Mini Hydraulic Excavators {5056}
335F Excavator Machine Systems Diagnostic Trouble Codes
311D, 312D, 312D2, 313D, 313D2, 314D, 315D, 318D, 318D2 and 319D Excavators Machine Electronic Control System MID 039 - CID 0017 - FMI 06
326F, 329F and 330F Excavators Machine Systems Window Wiper Motor - Remove and Install - Lower
311D, 312D, 312D2, 313D, 313D2, 314D, 315D, 318D, 318D2 and 319D Excavators Machine Electronic Control System MID 039 - CID 0017 - FMI 05
M313D, M315D, M315D Series 2, M315D2, M317D Series 2 and M317D2 Wheeled Excavators Hydraulic System Fan Motor (Hydraulic and Radiator Cooling) - Test
326F, 329F and 330F Excavators Machine Systems Window Wiper Motor - Remove and Install - Upper
326F, 329F and 330F Excavators Machine Systems Check Valve (Cooler Bypass) - Remove and Install
2013/09/20 Machine ECM Software has been Improved for Certain 300D Series Excavators {7610, 7620}
326F, 329F and 330F Excavators Machine Systems Hydraulic Lockout Control - Remove and Install
326F, 329F and 330F Excavators Machine Systems Seat - Remove and Install
326F, 329F and 330F Excavators Machine Systems Seat Support - Remove and Install
Installation Procedure for the 377-8218 Valve Wiring Gp on Certain Hydraulic Excavators{1408} Installation Procedure for the 377-8218 Valve Wiring Gp on Certain Hydraulic Excavators{1408}
2013/09/10 A New Monitor Software is Now Available for Certain Excavators {7490}
326F, 329F and 330F Excavators Machine Systems Seat Suspension - Remove and Install
302.5C Excavator TA2 Technical Inspection{0372, 1000, 7000, 753T, 7565} 302.5C Excavator TA2 Technical Inspection{0372, 1000, 7000, 753T, 7565}
336E OEM Excavator TA2 Technical Inspection{0372, 1000, 7000, 753T, 7565} 336E OEM Excavator TA2 Technical Inspection{0372, 1000, 7000, 753T, 7565}
2013/09/04 A New Machine Software is Now Available for Certain 336E H Excavators {7610, 7620}