Track - Connect
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 260-9412 | Chain As | 1 |
B | 5P-6214 | Track Block Assembly | 2 |
C | 5P-2379 | Track Press Tool Gp | 1 |
8S-7172 | Double Acting Cylinder | 1 | |
8S-9903 | Track Press Rollover Gp | ||
D | 1U-9200 | Lever Puller Hoist Gp | 1 |
- Use Tooling (D) in order to lift track assembly into place.
Show/hide table
Illustration 2 g02710747 -
Show/hide table
Illustration 3 g02706300 - Install track shoe (2) and bolts (1). Tighten bolts (1) to a torque of
400 ± 70 N·m (295 ± 52 lb ft) . Tighten bolts (1) by an additional 120 degrees.Show/hide tableIllustration 4 g02706319 - Remove Tooling (B) from both ends of the track assembly.
- Adjust the track tension.
Show/hide table
Illustration 1 | g02710740 |
Caterpillar Information System:
318E Excavator Systems Pump Control (Output Flow) - Adjust
Using the Cat 179-0710 Burn Rate Fuel Flow Measurement System {0374, 0599, 0706, 1250, 1280} Using the Cat 179-0710 Burn Rate Fuel Flow Measurement System {0374, 0599, 0706, 1250, 1280}
320E RR Excavator Machine Systems Track - Separate
349E HVG UHD Mobile Hydraulic Power Unit Reference Material
Installation Procedure for the 340-2918 Pilot Lines Gp On Certain Hydraulic Excavators{5057, 5059} Installation Procedure for the 340-2918 Pilot Lines Gp On Certain Hydraulic Excavators{5057, 5059}
G3500H 60Hz Generator Sets Coolant Temperature Regulator - Replace
G3500H 50Hz Generator Sets Rotating Rectifier - Check
320E and 323E Excavators Capacities (Refill)
Wiring Harness Medium Wheel Loader Coupler Supply Groups{6700} Wiring Harness Medium Wheel Loader Coupler Supply Groups{6700}
300.9D VPS Mini Hydraulic Excavator Machine Systems Basic Engine
301.4C Mini Hydraulic Excavator Basic Engine
300.9D VPS Mini Hydraulic Excavator Machine Systems Coolant Temperature Switch - Test
G310B, G315B, and G320B Demolition and Sorting Grapples Maintenance Interval Schedule
G310B, G315B, and G320B Demolition and Sorting Grapples Bearings (Cylinder Ends) - Lubricate
VRG-20/2, VRG-25/2 and VRG-30/2 Work Tools Maintenance Interval Schedule
VRG-20/2, VRG-25/2 and VRG-30/2 Work Tools Approved Machines
VRG-20/2, VRG-25/2 and VRG-30/2 Work Tools Bearings (Cylinder Ends) - Lubricate
C9.3 Engines for Caterpillar Built Machines Fuel System
C9.3 Engines for Caterpillar Built Machines General Information
C9.3 Engines for Caterpillar Built Machines Electronic Control System Components
320E RR Excavator Machine Systems Final Drive - Remove
320E RR Excavator Machine Systems Final Drive - Install
Procedure to Install the C-Series Bolt On Piercing Tip Shear Jaw Group to Certain Cat S365B and Verachtert VHS-60/3 Shears{5362, 6344} Procedure to Install the C-Series Bolt On Piercing Tip Shear Jaw Group to Certain Cat S365B and Verachtert VHS-60/3 Shears{5362, 6344}
374D and 390D Excavators Machine Electronic Control System MID 039 - CID 1145 - FMI 03