Lifter Group - Remove and Install
Removal Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 1U-7262     | Telescoping Magnet     | 1     |
Start By:
- Remove the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove ".
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Use Tool (A) to remove lifters (1) .
Note: Ensure that the lifters are marked with the appropriate cylinder number for installation purposes.
Show/hide table
Illustration 1 | g00540954 |
Installation Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 1U-7262     | Telescoping Magnet     | 1     |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Use Tool (A) to install lifters (1) .
Note: Ensure that the lifters are seated correctly and that the lifters are in the correct cylinders.
Show/hide table
Illustration 2 | g00540954 |
End By: Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Install".
Caterpillar Information System:
C-9 Industrial Engine CID 0110 FMI 04 Engine Coolant Temperature short to ground
2000/12/01 Change of Mounting Location for the Middle Vibration Isolator on All 3508 Generator Set Packages {1021}
C-9 Industrial Engine CID 0110 FMI 03 Engine Coolant Temperature open/short to +batt
3054 and 3056 Marine Generator Set Engines Crankshaft Front Seal - Install
3054 and 3056 Marine Generator Set Engines Crankshaft Front Seal - Remove
3606, 3608, 3612 and 3616 Engines and C280-12, C280-16, C280-6 and C280-8 Marine Engines Generator Monitoring System Thermocouple Module
3126B Industrial Engines CID 0100 FMI 03 Engine Oil Pressure open/short to +batt
C-10 and C-12 Industrial Engines Air Compressor
3003, 3013, 3014 and 3024 Industrial Engines Cylinder Head Bolts - Tighten
320E and 323E Excavators Boom and Stick Linkage - Lubricate - VA Boom (If Equipped)
C-10, C-12, C-15 and C-16 Industrial Engines Sensors and Electrical Connectors
3608 Engine Crankshaft Thrust - Measure
3054 and 3056 Marine Generator Set Engines Crankshaft Gear - Remove and Install
3126B Industrial Engines CID 0262 FMI 03 5 Volt Sensor DC Power Supply short to +batt
3126B Industrial Engines CID 0262 FMI 04 5 Volt Sensor DC Power Supply short to ground
3126B Industrial Engines CID 0273 FMI 03 Turbo Outlet Pressure open/short to +batt
3126B Industrial Engines CID 0273 FMI 04 Turbo Outlet Pressure short to ground
3126B Industrial Engines CID 0274 FMI 03 Atmospheric Pressure open/short to +batt
3126B Industrial Engines CID 0274 FMI 04 Atmospheric Pressure short to ground
C-10, C-12, C-15 and C-16 Industrial Engines Event Codes
C-10, C-12, C-15 and C-16 Industrial Engines E017 High Engine Coolant Temperature Warning
2001/01/01 New Engine Pressure Sensors are Available {1917, 1923, 1925}
3054, 3054B and 3056 Marine Engines Emissions Certification Film
Marine Monitoring System II Resistance Temperature Detector Module