Pads - Remove and Install
Show/hide table
Required Tooling | |||
Tool | Part Number | Part Description | Qty |
A | 138-7575 | Link Bracket | 3 |
Start By:
- Release the hydraulic system pressure. Refer to Disassembly and Assembly, "Hydraulic System Pressure - Release".
- Remove the buffer. Refer to the Disassembly and Assembly, "Buffer - Remove and Install".
Note: Always replace both pads if one or both of the set is damaged or worn.
- Ensure that the hammer is secure, in an upright position, and cannot fall.
Show/hide table
Illustration 1 g02644596 - Attach Tooling (A) and a suitable lifting device to hydraulic hammer (1). Refer to Table 2 for the approximate weight of hydraulic hammer (1).
Show/hide table
Table 2 Sales Model Hydraulic Hammer (1)
Approximate WeightH110E S 427 kg (942 lb) H115E S 481 kg (1060 lb) H120E S 691 kg (1524 lb) H130E S 875 kg (1929 lb) H140E 954 kg (2103 lb) H160E 1256 kg (2769 lb) H180E 1677 kg (3697 lb) - Slowly lift hydraulic hammer (1) enough to position suitable blocking. Position the blocking between the valve body of the hammer and the pad on the opposite side of the pad that is being replaced. Do not remove the hammer from the housing.
Show/hide table
Illustration 2 g02645456 - Use a suitable prybar to loosen pad (2). Remove pad (2). Repeat this step for the opposite side.
- Clean all parts and inspect all parts. If any parts are worn or damaged, use new Caterpillar parts for replacement.
Show/hide table
Illustration 3 g02645456 - Install pad (2). Repeat this step for the opposite side
Show/hide table
Illustration 4 g02644596 - Attach Tooling (A) and a suitable lifting device onto hydraulic hammer (1). Refer to Table 3 for the approximate weight of hydraulic hammer (1).
Show/hide table
Table 3 Sales Model Hydraulic Hammer (1)
Approximate WeightH110E S 427 kg (942 lb) H115E S 481 kg (1060 lb) H120E S 691 kg (1524 lb) H130E S 875 kg (1929 lb) H140E 954 kg (2103 lb) H160E 1256 kg (2769 lb) H180E 1677 kg (3697 lb) - Remove the suitable blocking and lower the hammer onto the pads.
- Ensure that the hammer is secure, in an upright position, and cannot fall.
End By:
- Install the buffer. Refer to the Disassembly and Assembly, "Buffer - Remove and Install".
Caterpillar Information System:
329E MHPU Mobile Hydraulic Power Unit Maintenance Interval Schedule
G3512 Gas Engine Flywheel
330D and 336D Excavators Machine System Specifications Stick Cylinder
330D and 336D Excavators Machine System Specifications Return and Oil Filter Lines
301.4C Mini Hydraulic Excavator Travel Motor
301.4C Mini Hydraulic Excavator Hydraulic System Breather - Replace
301.4C Mini Hydraulic Excavator Fuel Injection Nozzles - Check/Adjust
301.4C Mini Hydraulic Excavator Hydraulic System Oil Filter (Pilot) - Check/Replace
301.4C Mini Hydraulic Excavator Swing Gear Grease - Check
345B Series II Excavator Machine System Specifications Bucket Cylinder
VHS-60/4 and VHS-70/4 Demolition and Scrap Shears Hydraulic Rotator Cycle Time - Check
VHS-60/4 and VHS-70/4 Demolition and Scrap Shears Hydraulic Cylinder Cycle Time - Check
320E RR Excavator Hydraulic System Swing Motor - Test - Measurement of Case Drain Oil
Instructions for Replacing the Support Plate on Certain SW60 Wheel Saws{6712} Instructions for Replacing the Support Plate on Certain SW60 Wheel Saws{6712}
320E RR Excavator Hydraulic System Relief Valve (Swing) - Test and Adjust
330D and 336D Excavators Machine System Specifications Hydraulic Generator
H110ES, H115ES, H120ES, H130ES, H140ES, H160ES and H180ES Hydraulic Hammers Wear Plates - Remove and Install
H110ES, H115ES, H120ES, H130ES, H140ES, H160ES and H180ES Hydraulic Hammers Control Valve - Remove
H110ES, H115ES, H120ES, H130ES, H140ES, H160ES and H180ES Hydraulic Hammers Control Valve - Install
G310B, G315B and G320B Demolition and Sorting Grapples Hydraulic Rotator Cycle Time - Check
G310B, G315B and G320B Demolition and Sorting Grapples Host Machine Pressure and Flow - Test
H110ES, H115ES, H120ES, H130ES, H140ES, H160ES and H180ES Hydraulic Hammers Pressure Control Valve - Remove
H110ES, H115ES, H120ES, H130ES, H140ES, H160ES and H180ES Hydraulic Hammers Pressure Control Valve - Install
Intake Manifold Pressure Shown Incorrectly in the Monitor Display of Certain Wheeled Excavators{7490, 7601, 7620} Intake Manifold Pressure Shown Incorrectly in the Monitor Display of Certain Wheeled Excavators{7490, 7601, 7620}