Hydraulic Rotator Cycle Time - Check
- Turn off the engine of the host machine and activate the parking brake.
- Conduct a good visual inspection of all hoses, fittings, and components. If any leaks or damage is observed, repair the problem before you attempt this check.
- Start the host machine and operate the implements until the hydraulic oil reaches normal operating temperature.
Note: The host machine must be operated at high idle during this check.
- Raise the work tool from the ground. Position the work tool in a perpendicular position with the ground. Refer to Illustration 1.
Show/hide table
Illustration 1 | g00986410 |
- Note the starting position of the work tool and rotate the work tool in one direction. Record the number of rotations that are completed in 1 minute.
Show/hide table
Table 1 Cycle Time     Sales Model     Revolutions Per Minute (RPM)     G310B     11     G315B     11     G320B     9    
- If the rpm was within the specification, the work tool is rotating properly. If the rpm was not within the specification, check the oil flow and the oil pressure of the host machine. Refer to the Service Manual, "Host Machine Pressure and Flow - Test".
- If an adjustment was made to the host machine, repeat the check.
Caterpillar Information System:
H110ES, H115ES, H120ES, H130ES, H140ES, H160ES and H180ES Hydraulic Hammers Control Valve - Install
H110ES, H115ES, H120ES, H130ES, H140ES, H160ES and H180ES Hydraulic Hammers Control Valve - Remove
H110ES, H115ES, H120ES, H130ES, H140ES, H160ES and H180ES Hydraulic Hammers Wear Plates - Remove and Install
330D and 336D Excavators Machine System Specifications Hydraulic Generator
320E RR Excavator Hydraulic System Relief Valve (Swing) - Test and Adjust
Instructions for Replacing the Support Plate on Certain SW60 Wheel Saws{6712} Instructions for Replacing the Support Plate on Certain SW60 Wheel Saws{6712}
320E RR Excavator Hydraulic System Swing Motor - Test - Measurement of Case Drain Oil
H110ES, H115ES, H120ES, H130ES, H140ES, H160ES and H180ES Hydraulic Hammers Pads - Remove and Install
329E MHPU Mobile Hydraulic Power Unit Maintenance Interval Schedule
G3512 Gas Engine Flywheel
330D and 336D Excavators Machine System Specifications Stick Cylinder
330D and 336D Excavators Machine System Specifications Return and Oil Filter Lines
G310B, G315B and G320B Demolition and Sorting Grapples Host Machine Pressure and Flow - Test
H110ES, H115ES, H120ES, H130ES, H140ES, H160ES and H180ES Hydraulic Hammers Pressure Control Valve - Remove
H110ES, H115ES, H120ES, H130ES, H140ES, H160ES and H180ES Hydraulic Hammers Pressure Control Valve - Install
Intake Manifold Pressure Shown Incorrectly in the Monitor Display of Certain Wheeled Excavators{7490, 7601, 7620} Intake Manifold Pressure Shown Incorrectly in the Monitor Display of Certain Wheeled Excavators{7490, 7601, 7620}
320E RR Excavator Hydraulic System Relief Valve (Crossover) - Test and Adjust
H110ES, H115ES, H120ES, H130ES, H140ES, H160ES and H180ES Hydraulic Hammers Pressure Control Valve - Disassemble
H110ES, H115ES, H120ES, H130ES, H140ES, H160ES and H180ES Hydraulic Hammers Pressure Control Valve - Assemble
320E RR Excavator Hydraulic System Main Pump (Flow) - Test - Constant Horsepower Flow Control
330D and 336D Excavators Machine System Specifications Hydraulic Generator
330D, 336D, 336D2, 340D and 340D2 Excavators Machine System Specifications Travel Motor Guard
325D and 329D Excavators Machine System Specifications Travel Counterbalance Valve
330C Forest Machine Machine System Specifications Track