Setpoint Viewing and Programming
The Setpoint Viewing/Programming menu is entered by pressing the "MODE" button from the Fault Viewing/Clearing menu or the I/O Monitoring/Programming menu. The Setpoint Viewing/Programming menu allows the operator to view program PRCM setpoints. The Setpoint Viewing/Programming menu also allows the operator to program the PRCM setpoints.
Show/hide table
PRCM SETPOINTS     | ||
Setpoint Number     | Setpoint Value     | Description     |
P01     | 01     | Genset or center marine engine.     |
02 | Port marine engine.     | |
03 | Starboard marine engine.     | |
P02     | 01     | All outputs controlled by the ECM remain in the state required by the last valid input, if communications from the ECM are lost (CAT data link failure).     |
02 | All outputs controlled from the ECM are reset to OFF.     | |
P03     | 01     | PRCM displays CID 590 FMI 09 and CID 248 FMI 11 diagnostic codes when the diagnostic codes are active, but does NOT place the diagnostic codes in the PRCM fault log.     |
02 | PRCM displays CID 590 FMI 09 and CID 248 FMI 11 diagnostic codes when the codes are active and places the diagnostic codes in the fault log.     |
The upper display will be blank and the lower display will show "P01 0X". The "X" represents 1, 2, or 3. The 1, 2, and 3 represents the different types of engines.
Show/hide table
Illustration 1 | g00713203 |
In the following example, the setpoint "P01" is programmed to "02". A "02" is for the marine engine that is located on the port side.
- The "UP" and "DOWN" buttons are used in order to scroll through the list of setpoints.
- To program a setpoint, press the "ENTER" button. The password must be entered before the operator is allowed to enter the programming function. Refer to Systems Operation, "Input/Output Monitoring and Programming" for detailed instructions on entering the password. After you enter the password, the setpoint number should be flashing.
- Use the "UP" and "DOWN" buttons to obtain the desired setpoint.
- Press the "LEFT" and "RIGHT" button. The setpoint value is flashing.
Show/hide table
Illustration 2 | g00713210 |
- Use the "UP" and "DOWN" buttons in order to change the value of the setpoints.
Show/hide table
Illustration 3 | g00713215 |
- Press the "LEFT" and "RIGHT" button. All the characters flash.
Show/hide table
Illustration 4 | g00713215 |
- Press the "LEFT" and "RIGHT" button in order to reject the changes. Press the "SELECT" button in order to accept the changes. The display will stop flashing for two seconds. When the display of the setpoint number begins to flash the operator is allowed to start programming the next setpoint.
- After programming is complete, press "ENTER"in order to leave the programming mode and return to viewing the setpoints.
Caterpillar Information System:
G3516B Engines E865 High Gas Fuel Differential Pressure
3500B Engines for Caterpillar Built Power Modules with the ADEM 2 Electronic Control Module System Configuration Parameters
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Fuel System - Inspect
G3516B Engines E864 Low Gas Fuel Differential Pressure
G3516B Engines E856 Cyl #16 Exhaust Port Temp Deviating Low
G3516B Engines E855 Cyl #15 Exhaust Port Temp Deviating Low
G3516B Engines E854 Cyl #14 Exhaust Port Temp Deviating Low
G3516B Engines E853 Cyl #13 Exhaust Port Temp Deviating Low
G3516B Engines E852 Cyl #12 Exhaust Port Temp Deviating Low
G3516B Engines E851 Cyl #11 Exhaust Port Temp Deviating Low
G3516B Engines E850 Cyl #10 Exhaust Port Temp Deviating Low
G3516B Engines E849 Cyl #9 Exhaust Port Temp Deviating Low
G3516B Engines E866 Low Gas Fuel Flow Rate
2000/06/01 New Hydraulic Wrenches and Pumps {0602, 0615}
3126B and 3126E On-highway Engines Intermittent Engine Shutdown
Installation Instructions for 192-1511 Air Conditioner Gp and for 192-5372 Air Conditioner Gp {7320} Installation Instructions for 192-1511 Air Conditioner Gp and for 192-5372 Air Conditioner Gp {7320}
Programmable Relay Control Module (PRCM) Service Tools
Programmable Relay Control Module (PRCM) General Information
Programmable Relay Control Module (PRCM) Fault Identification
G3516B Engines Engine Speed/Timing Sensor - Calibrate
2002/05/20 Improved Electric Fuel Shutoff Solenoid {1259}
3126B and 3126E On-highway Engines Intermittent Low Power or Power Cutout
3034 Engine for Caterpillar Built Machines Fuel Shutoff Solenoid - Test
G3516B Engines E867 Improper Gas Flow Control Valve Response