Improvements to the Carrier Assembly On Brush Cutters {670B}
- Work Tool:
- BR160 (S/N: SDB1-UP)
- BR166 (S/N: SWB1-UP)
- BR172 (S/N: TAB1-UP)
- BR272 (S/N: DLY1-UP)
- BR378 (S/N: RDN1-UP)
Description of Change: A design change to the bolted joint increases the contact area of the bolt and carrier assembly on the above listed brush cutters. The improved carrier allows the increased preload for the size of the bolts.
Adaptable To: The new carrier assembly is effective with the models in Table 1.
The necessary components for the replacement of the carrier assembly are listed in Table 2.
Show/hide table
Machine Effectivity     | ||
---|---|---|
Model     | Adaptability     | Effectivity     |
BR160     | S/N:SDB1-234     | S/N:SDB235-UP     |
BR166     | S/N:SWB1-354     | S/N:SWB355-UP     |
BR172     | S/N:TAB1-626     | S/N:TAB627-UP     |
BR272     | S/N:DLY1-245     | S/N:DLY246-UP     |
BR378     | S/N:RDN1-167     | S/N:RDN168-UP     |
Show/hide table
Parts List     | ||||
---|---|---|---|---|
Item     | Qty     | Part Number     | Desc.     | Former Part No.     |
1     | 1     | 291-6547     | Carrier As     | 264-9553     |
2     | 2     | 8T-5361     | Hard Washer     | 271-2353     |
3     | 2     | 2K-7471     | Locknut     | 3D-4904     |
4     | 2     | 280-6820     | Pin     | 264-9552     |
Show/hide table
Illustration 1 | g01299718 |
(A)
- Torque for the bolt ... 610 ± 80 N·m (450 ± 60 lb ft)
(B)
- Torque for the bolts ... 1050 ± 80 N·m (775 ± 60 lb ft)
Note: (B) Optional torque turn method. Tighten the nut to an initial torque of 500 N·m (370 lb ft). Turn the nut an additional 60 degrees in order to achieve the required 1050 ± 80 N·m (775 ± 60 lb ft) torque value.
Caterpillar Information System:
390D Excavator Machine Systems Swing Control Valve - Install
365C Excavator Counterweight Removal and Installation
C4.2 and C6.4 Engines for Caterpillar Built Machines Electrical Connectors - Inspect
390D Excavator Machine Systems Swing Control Valve - Remove
390D Excavator Machine Systems Swing Motor - Install - Rear
M325D L MH and M325D MH Material Handlers Hydraulic System Main Hydraulic System
2006/08/14 Refrigerant Identification Instrument is Available {1809}
C175-16 and C175-20 Engines for Off-Highway Trucks Air Starting System
M330D Material Handler Lifting Capacities
330D Material Handler Hydraulic System Relief Valve (Medium Pressure Function) - Test and Adjust - Hydraulic Cab Riser
390D Excavator Machine Systems Swing Motor - Remove - Rear
M325D L MH and M325D MH Material Handlers Hydraulic System Stick Hydraulic System
M330D Material Handler Lifting Capacities
330D Material Handler Hydraulic System Relief Valve (Medium Pressure Function) - Test and Adjust - Rotate Circuit
3500C Marine Auxiliary Engines Factory Passwords
The Positive Wire Terminal May Break at the Alternator's Positive Post{1405} The Positive Wire Terminal May Break at the Alternator's Positive Post{1405}
M330D Material Handler Lifting Capacities
2006/08/28 The Design For The Trencher's Chain Tension Adjuster Has Been Updated {4159, 671C}
C4.4 and C6.6 Engines For Caterpillar Built Machines Engine Misfires, Runs Rough or Is Unstable
2006/08/28 A New Piston Pump is Available for Field Repairs {5070}
C4.2 and C6.4 Engines for Caterpillar Built Machines Engine Speed Does Not Change
C4.4 and C6.6 Engines For Caterpillar Built Machines Engine Stalls at Low RPM
C7 Engines for Caterpillar Built Machines Valve Mechanism
2006/08/07 Correct Operation of Load Control Valves on Mini Hydraulic Excavators {5811}