System Configuration Parameters
Certain parameters are unique for each engine application. Table 1 is a list of the parameters that can be configured for G3516B Engines. The parameters are programmed into the Electronic Control Module (ECM) via the Caterpillar Electronic Technician (Cat ET). The values of the parameters can be viewed on the "Configuration" screen of Cat ET.
Most of the parameters are common to engines that use oxygen feedback and to engines that use charge density. However, some of the parameters are associated only with oxygen feedback or with charge density.
Refer to Systems Operation/Testing and Adjusting, "Electronic Control System Parameters" for the descriptions of the parameters.
Show/hide table
| Configuration Parameters for G3516B Engines | |||||
|---|---|---|---|---|---|
| Parameter | Oxygen Feedback | Charge Density | |||
| Timing Control | |||||
| "First Desired Timing" | Yes | Yes | |||
| "Second Desired Timing" | Yes | Yes | |||
| Air/Fuel Ratio Control | |||||
| "Fuel Quality" | Yes | Yes | |||
| "Gas Specific Gravity" | Yes | Yes | |||
| "Desired Oxygen at Full Load" | Yes | No | |||
| "Oxygen Feedback Enable Status" | Yes | No | |||
| "Fuel Specific Heat Ratio" | No | Yes | |||
| "Desired Emission Gain Adjustment" | No | Yes | |||
| "Air/Fuel Proportional Gain" | Yes | Yes | |||
| "Air/Fuel Integral Gain" | Yes | Yes | |||
| Speed Control | |||||
| "Low Idle Speed" | Yes | Yes | |||
| "Minimum High Idle Speed" | Yes | Yes | |||
| "Maximum High Idle Speed" | Yes | Yes | |||
| "Engine Accel. Rate" | Yes | Yes | |||
| "Desired Speed Input Configuration" | Yes | Yes | |||
| "Governor Type Setting" | Yes | Yes | |||
| "Engine Speed Droop" | Yes | Yes | |||
| "Governor Proportional Gain" | Yes | Yes | |||
| "Governor Integral Gain" | Yes | Yes | |||
| "Governor Derivative Gain" | Yes | Yes | |||
| "Auxiliary Proportional Governor Gain 1" | Yes | Yes | |||
| "Auxiliary Integral Governor Gain 1" | Yes | Yes | |||
| "Auxiliary Derivative Governor Gain 1" | Yes | Yes | |||
| Start/Stop Control | |||||
| "Driven Equipment Delay Time" | Yes | Yes | |||
| "Crank Terminate Speed" | Yes | Yes | |||
| "Engine Purge Cycle Time" | Yes | Yes | |||
| "Engine Cooldown Duration" | Yes | Yes | |||
| "Cycle Crank Time" | Yes | Yes | |||
| "Engine Overcrank Time" | Yes | Yes | |||
| "Engine Speed Drop Time" | Yes | Yes | |||
| "Engine Pre-lube Time Out Period" | N/A | ||||
| Monitoring and Protection | |||||
| "High Inlet Air Temp Load Set Point" | Yes | Yes | |||
| Power Monitoring | |||||
| "Generator Output Power Sensor Scale Factor" | Yes | Yes | |||
| "Generator Output Power Sensor Offset" | Yes | Yes | |||
| "Engine Output Power Configuration" | No | Yes | |||
| "Engine Driven Accessory Load Configuration" | No | Yes | |||
| Information for the ECM | |||||
| "Engine Serial Number" | Yes | Yes | |||
| "Equipment ID" | Yes | Yes | |||
| "Customer Password #1" | Yes | Yes | |||
| "Customer Password #2" | Yes | Yes | |||
| "Total Tattletale" | Yes | Yes | |||
Caterpillar Information System:
3126B and 3126E On-highway Engines System Overview
2003/01/01 Two Strainers are Available to Protect the Bearings in Turbochargers {1052}
3512B Petroleum Engine Radiator - Clean
Electronic Modular Control Panel II (EMCP II) Instrument Panel
3512B Petroleum Engines Testing the Radiator and Cooling System for Leaks
2000/05/01 Water Lines Groups (ECM Coolant Lines) Have Been Removed {1380}
Connection Diagrams: SR4 and SR4B Generators, Voltage Regulators, Options General Information (All Except SR4B for 3500 Engines)
3512B Petroleum Engines System Configuration Parameters
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Engine Lifting Bracket
Connection Diagrams: SR4 and SR4B Generators, Voltage Regulators, Options Options (SR4B for 3500 Engines)
Connection Diagrams: SR4 and SR4B Generators, Voltage Regulators, Options Digital Voltage Regulator Connections (SR4B for 3500 Engines)
Connection Diagrams: SR4 and SR4B Generators, Voltage Regulators, Options VR3 Voltage Regulator Connections (SR4B for 3500 Engines)
2000/06/01 A New Inlet Valve is Released for use in 3116 and 3126 Truck Engines with the Two Valve Configuration. {1105}
2000/08/01 New Components in Jacket Water Heater Groups Provide Improved Sealing {1383}
3618 Engine Fuel Conservation Practices
3126B Marine Engine Engine Electronics
Uninterruptible Power Supply (UPS) 250 AC Current - Calibrate
Uninterruptible Power Supply (UPS) 250 AC Voltage - Calibrate
Uninterruptible Power Supply (UPS) 250 DC Buss Voltage - Calibrate
2000/04/10 Special Instruction, REHS0440 is Available for an Index of Electrical System Schematics {7566}
Uninterruptible Power Supply (UPS) 250 Flywheel Telemetry - Calibrate
3126B Marine Engine Self-Diagnostics
3114, 3116, and 3126 Engines Basic Engine
C-10, C-12, C-15 and C-16 Industrial Engines CID 0320 FMI 02 Speed/Timing Sensor Loss of Signal