Fuel System - Inspect
Show/hide table
| 注意 |
|---|
请确保对燃油系统进行的所有调整和修理均由经过适当培训的授权人员执行。 在燃油系统上开始任何工作之前，请参阅操作和保养手册, "一般危险信息和高压燃油管路"以了解安全信息。 有关在所有燃油系统工作期间必须遵循的清洁度标准的详细信息，请参阅系统运作，测试和调整, "燃油系统部件清洁度"。 |
将燃油输送到发动机的部件如果有问题，将会导致燃油压力低。 这会使发动机性能降低。
- 检查燃油箱中的燃油油位。 确保油箱盖的通气孔没有被灰尘阻塞。
- 检查燃油管有无泄漏。 油管必须没有阻塞和与规格不符的弯折。 检验回油管有无皱缩。
- 安装新燃油滤清器。
- 使用适当的滤清器切割机割开旧的滤清器。 检查滤清器有无过多杂质。 确定杂质的源头。 进行必要的修理。
- 操作手动注油泵（如有配备）。 如果感觉到阻力过大，请检查到油箱的回油管中有无燃油。
测量通过燃油喷油器的燃油泄漏。
如果通过电子单体喷油器的燃油泄漏过大，请参阅专门说明书, KENR6938, "电子单体喷油器高泄漏"。
Caterpillar Information System:
C7.1 Engines for Caterpillar Built Machines Engine Oil Cooler - Inspect
C6.6 Engines for Caterpillar Built Machines Fuel System - Prime
C13, C15, and C18 Tier 4 Final Engines Engine Oil Pan
320D, 320D2, 321D, 323D, 324D, 325D, 328D, 329D, 330D, 336D, 336D2, 340D and 340D2 Excavators Tool Control System Process for Setting Up the Work Tool
PR172, PR184 and PR190 Power Rake Work Tool Installation and Removal
Shop Repair Procedure for Grease Lubricated Track {0729, 4169, 4170, 4175} Shop Repair Procedure for Grease Lubricated Track {0729, 4169, 4170, 4175}
324D Excavator Hydraulic System Cylinder Speed - Check
Index of Wall Charts for Drivetrain, Engine, Hydraulics, and Undercarriage{1000, 4000, 4150, 5050} Index of Wall Charts for Drivetrain, Engine, Hydraulics, and Undercarriage{1000, 4000, 4150, 5050}
PR172, PR184 and PR190 Power Rake Lifting and Tying Down
PR172, PR184 and PR190 Power Rake Frame Mounting Bracket - Inspect
324D Excavator Hydraulic System Swing Speed and Swing Drift on a Slope - Check
320D, 320D2, 321D, 323D, 324D, 325D, 328D, 329D, 330D, 336D, 336D2, 340D and 340D2 Excavators Tool Control System Service Tools
Guideline for Examining Failed Parts{1000, 7000} Guideline for Examining Failed Parts{1000, 7000}
M313D, M315D, M316D, M318D and M322D Wheeled Excavators and M318D MH and M322D MH Wheeled Material Handlers Hydraulic System General Testing and Adjusting Information
PR172, PR184 and PR190 Power Rake Transport Position
PR172, PR184 and PR190 Power Rake Reference Material
325D and 329D Excavators Hydraulic System Pump Control (Negative Flow) - Adjust
Bench Test Procedure for Hydraulic Piston Pumps{5070} Bench Test Procedure for Hydraulic Piston Pumps{5070}
PR172, PR184 and PR190 Power Rake Bearing - Lubricate
324D Excavator Hydraulic System Travel on Level Ground - Test
324D Excavator Hydraulic System Travel on Level Ground - Test - Optional Test
C15 and C18 Engines for Caterpillar Built Machines Exhaust Manifold
PR172, PR184 and PR190 Power Rake Chain Case Lubricant - Change
3508 EUI Engines for Caterpillar Built Machines Muffler