Crankshaft Position for Fuel Injector Adjustment and Valve Lash Setting
Show/hide table
| 从发动机的飞轮端观看发动机，其旋向为逆时针方向（标准） | ||||
|---|---|---|---|---|
| 可进行相应的检查/调整的气缸 | ||||
| 发动机 | 1 号活塞位于上死点位置的正确冲程。(1) | 进气门 | 排气门 | 喷油器 |
| 3508 | 压缩 | 1-2-6-8 | 1-2-3-7 | 2-3-4-7 |
| 排气 | 3-4-5-7 | 4-5-6-8 | 1-5-6-8 | |
| 3512 | 压缩 | 1-3-6-7-10-12 | 1-4-5-6-9-12 | 2-4-5-8-9-11 |
| 排气 | 2-4-5-8-9-11 | 2-3-7-8-10-11 | 1-3-6-7-10-12 | |
| 3516 | 压缩 | 1-2-5-7-8-12-13-14 | 1-2-3-4-5-6-8-9 | 3-4-5-6-9-10-15-16 |
| 排气 | 3-4-6-9-10-11-15-16 | 7-10-11-12-13-14-15-16 | 1-2-7-8-11-12-13-14 | |
Show/hide table
| (1) | 将 1 号活塞置于上止点 (TC) 位置，确定正确冲程。 请参阅测试与调整, "确定 1 号活塞上止点位置"。 确定针对某一冲程的上止点位置，并进行对应于此冲程的正确的气缸的相应调整。 拆下正时螺栓。 沿发动机正常旋转方向将飞轮转动 360 度。 转动飞轮可将 1 号活塞置于其他冲程的上止点 (TC) 位置。 将正时螺栓安装到飞轮中，然后完成针对其余气缸的调整。 |
Show/hide table
| 从发动机的飞轮端观看发动机，其旋向为顺时针方向（反转） | ||||
|---|---|---|---|---|
| 需要进行检查/调整的气缸 | ||||
| 发动机 | 1 号活塞位于上死点位置的正确冲程。(1) | 进气门 | 排气门 | 喷油器 |
| 3508 | 压缩 | 1-3-4-8 | 1-2-7-8 | 2-6-7-8 |
| 排气 | 2-5-6-7 | 3-4-5-6 | 1-3-4-5 | |
| 3512 | 压缩 | 1-3-4-6-7-12 | 1-4-5-8-9-12 | 2-5-8-9-10-11 |
| 排气 | 2-5-8-9-10-11 | 2-3-6-7-10-11 | 1-3-4-6-7-12 | |
| 3516 | 压缩 | 1-2-5-6-7-8-13-14 | 1-2-3-4-5-6-9-10 | 3-4-5-9-10-12-15-16 |
| 排气 | 3-4-9-10-11-12-15-16 | 7-8-11-12-13-14-15-16 | 1-2-6-7-8-11-13-14 | |
Show/hide table
| (1) | 将 1 号活塞置于上止点 (TC) 位置，确定正确冲程。 请参阅测试与调整, "确定 1 号活塞上止点位置"。 确定针对某一冲程的上止点位置，并进行对应于此冲程的正确的气缸的相应调整。 拆下正时螺栓。 沿发动机正常旋转方向将飞轮转动 360 度。 转动飞轮可将 1 号活塞置于其他冲程的上止点 (TC) 位置。 将正时螺栓安装到飞轮中，然后完成针对其余气缸的调整。 |
Caterpillar Information System:
325D and 329D Excavators Engine Air Filter Secondary Element - Replace
325D and 329D Excavators Cooling System Coolant Level - Check
321B LCR Excavator Cooling System Coolant Extender (ELC) - Add
3406C Truck Engine Coolant Temperature Above Normal
325D and 329D Excavators Bucket Linkage - Inspect/Adjust
723PLUS Digital Speed Control Programming Checklist
3034 Engine for Caterpillar Built Machines Rocker Shaft
723PLUS Digital Speed Control Serial Communication Port Wiring
2000/03/13 Machine Fluids Recommendations are Moved to Operation and Maintenance Manual, SEBU6250, "Caterpillar Machine Fluids Recommendations" {1000, 1250, 1280, 1300, 1348, 1350, 1352, 1395, 3080, 4000, 4250, 5095, 7000, 7542, 7551, 7579, 7581}
723PLUS Digital Speed Control Service Options
C-12, C-15 and C-16 Engines for Caterpillar Built Machines CID 0006 FMI 11 Injector Cylinder #6 fault
723PLUS Digital Speed Control Conclusion of Test and Calibration Procedures
3406C Truck Engine Coolant Temperature Below Normal
797 Off-Highway Truck Power Train Rear Wheel and Differential Fastener
3406C Truck Engine Engine Cranks but Will Not Start
Electronic Modular Control Panel II+ (EMCP II+) Starting Motor Magnetic Switch - Test - EUI Engines Only
Electronic Modular Control Panel II+ (EMCP II+) Starting Motor Magnetic Switch - Test - PEEC Engines Only
P16, P20, P25, P28, P40 and P60 Pulverizers Hydraulic Cylinder - Remove
2000/04/01 New Water Pump Group Includes Many Improvements {1361}
Electronic Modular Control Panel II+ (EMCP II+) Spare Input/Output Programming OP6 - For EUI And PEEC Engines
325D and 329D Excavators Fuel Tank Cap and Strainer - Clean
3408E and 3412E Industrial Engines CAT Data Link Circuit - Test
723PLUS Digital Speed Control Control Specifications
G3516B Engines System Overview