Make sure that all of the messages are legible. Clean the messages or replace the messages if you cannot read the words. Replace the illustrations if the illustrations are not legible. When you clean the messages, use a cloth, water, and soap. Do not use solvent, gasoline, or other harsh chemicals to clean the messages. Solvents, gasoline, or harsh chemicals could loosen the adhesive that secures the messages. Loose adhesive will allow the messages to fall.
Replace any message that is damaged, or missing. If a message is attached to a part that is replaced, install a message on the replacement part. Any Caterpillar dealer can provide new messages.
Illustration 1 | g01441151 |
Additional messages inside cab (if equipped) |
Illustration 2 | g01441153 |
Additional messages inside cab (if equipped) |
Illustration 3 | g01441154 |
Additional messages inside cab (if equipped) |
Illustration 4 | g01441508 |
Cleaning Windows (1)
This message is located in three places on the cab windows.
Illustration 5 | g01134495 |
See Operation and Maintenance Manual, "Windows - Clean" for instructions on cleaning windows.
Alternate Exit (2)
This message is located on the rear window in the cab.
Illustration 6 | g00915906 |
If the primary exits are blocked, pull the ring in order to open the rear window. Exit the machine through the window.
Ring for the Alternate Exit (3)
This message is located on the ring for the alternate exit.
Illustration 7 | g00915912 |
Pull the ring in order to open the alternate exit.
Product Link (4)
This message is located on the window on the right side of the cab.
Illustration 8 | g01418953 |
The Product Link System is a satellite communication device that transmits information regarding the machine back to Caterpillar and Caterpillar dealers and customers. All logged events and diagnostic codes that are available to the Caterpillar Electronic Technician (ET) on the CAT data link can be sent to the satellite. Information can also be sent to the Product Link System. The information is used to improve Caterpillar products and Caterpillar services.
Refer to Operation and Maintenance Manual, "Product Link" for more information.
Alternate Exit Lock/Unlock (5)
This message is located on the rear window in the cab.
Illustration 9 | g01025557 |
Move the lever to the left to the UNLOCK position. Move the lever to the right to the LOCK position.
Alternate Exit (6)
This message is located on the rear window of the cab.
Illustration 10 | g00937088 |
NOTICE |
---|
Unlock alternate exit window during machine operations. |
Alternate Exit (7)
This message is located on the rear window of the cab.
Illustration 11 | g00911516 |
Exit through the rear window.
Hammer for the Alternate Exit (8)
This message is located at the rear of the cab.
Illustration 12 | g00907967 |
If the primary exits are blocked, use the hammer to break the window. Exit the machine through the window.
Radial Seal Air Filters (9)
This message is located on the air cleaner.
Illustration 13 | g01134494 |
To avoid engine damage, use only Caterpillar radial seal air filters. Other filters will not seal properly.
Refer to Operation and Maintenance Manual, "Engine Air Filter Primary Element - Clean/Replace" for more information.
Cab Retention Bolts (10)
This message is located to the side of the rear cab retention bolts.
Illustration 14 | g01441509 |
Do not remove the cab retention bolts. Ensure that a proper lifting device is attached to the cab.
Refer to Operation and Maintenance Manual, "Cab Tilting" for the procedure to remove cab retention bolts.
Adjustable Gage Undercarriage Frame (11)
This message is located on the front of the track frames of the machine.
Illustration 15 | g01110727 |
Reference: Refer to Operation and Maintenance Manual, "Adjustable Gage Undercarriage Frame" for the procedure to adjust the undercarriage frame.