Override Mode
用户可以使用 "OVERRIDE（超弛）"菜单超弛系统部件以帮助进行故障诊断和排除流程。
Show/hide table
| |
| 图 1 | g01152977 |
|
(8) 向上键
(9) 向右键 (10) 归位键 (11) 主菜单键 (12) 向左键 (13) 向下键 (14) 取消键或返回键 (15) 确定键 | |
从 "SERVICE（维修）"菜单中选择 "OVERRIDE（诊断）"可进入 "OVERRIDE（诊断）"菜单选项。 按向上键 (8) 或向下键 (13) 直到 "OVERRIDE（诊断）"突出显示，以便选择此选项。 然后按下"确定"键 (15)。 请参阅插图 2。
注: 请参阅系统运作, "维修模式"以了解使用 "SERVICE（维修）"菜单的简介。
Show/hide table
| |
| 图 2 | g01152160 |
按向上键 (8) 或向下键 (13) 以突出显示要超弛的项目。
Show/hide table
| |
| 图 3 | g01152162 |
将光标移到所需的参数后，请使用相应的键更改参数值。 按"确定"键 (15) 以开始超弛。
Show/hide table
| |
| 图 4 | g01152164 |
要停止超弛，请突出显示该项目并按向左键 (12)。
请参阅表 1 以获得 "OVERRIDE（超弛）"菜单中可用的系统部件列表。
Show/hide table
| 超弛信息列表 | |||
|---|---|---|---|
| 显示 | 345C
324D 325D 330D |
365C
385C |
详细信息 |
| "DESIRED ENG SPEED（所需发动机转速）" | X | X | 所需的发动机转速 |
| "FAN MOTOR SPEED（风扇马达转速）" | X | X | 风扇马达转速 |
| "TRV SPEED SHIFT（行驶速度换挡）" | X | X | 行驶速度电磁阀超弛 |
| "SWING BREAK SOL（停车制动器电磁阀）" | X | X | 停车制动器电磁阀超弛 |
| "TRV ALARM（行驶报警）" | X | X | 行驶报警超弛 |
| "系统自检 (SYSTEM PRES UP)" | X | 前端系统高压电磁阀超弛 | |
| "NEUTRAL FLOW BYPASS（中档流量旁通）" | X | 中档流量旁通电磁阀超弛 | |
| "ANTI DRIFT BOOM（防沉降动臂）" | X | 动臂防沉降电磁阀超弛 | |
| "ANTI DRIFT STICK（防沉降斗杆）" | X | 斗臂防沉降电磁阀超弛 | |
| "辅助转向继电器 (AUTO LUB RELAY)" | X | 自动润滑电磁阀超弛 | |
| "REVERSE FAN SOL（逆向风扇电磁阀）" | X | X | 自动逆向风扇电磁阀超弛 |
| "1P/2P CHANGE SOL（1P/2P 转换电磁阀）" | X | 辅助回路电流组合电磁阀超弛 | |
| "FAULT ALARM（故障报警）" | X | 行动警报超弛 | |
| "1/2 WAY CHANGE SOL（单向/双向转换电磁阀）" | X | 单向/双向阀电磁阀超弛 | |
| "RELIEF CHK SOL #1（1 号安全单向电磁阀）" | X | 1 号安全单向电磁阀超弛 | |
| "RELIEF CHK SOL #2（2 号安全单向电磁阀）" | X | 2 号安全单向电磁阀超弛 | |
| "BOOM EXTEND（动臂伸出）" | X | 动臂油缸连杆伸出电磁阀电流超弛 | |
| "BOOM RETRACT（动臂回缩）" | X | 动臂油缸连杆回缩电磁阀电流超弛 | |
| "STICK EXTEND（斗杆伸出）" | X | 斗杆油缸连杆伸出电磁阀电流超弛 | |
| "STICK RETRACT（斗杆回缩）" | X | 斗杆油缸连杆回缩电磁阀电流超弛 | |
| "BUCKET EXTEND（铲斗伸出）" | X | 铲斗油缸连杆伸出电磁阀电流超弛 | |
| "BUCKET RETRACT（铲斗回缩）" | X | 铲斗油缸连杆回缩电磁阀电流超弛 | |
| "SWING LEFT（左回转）" | X | 左回转电磁阀电流超弛 | |
| "SWING RIGHT（向右回转）" | X | 右回转电磁阀电流超弛 | |
| "TRV LEFT FW（左前进行驶）" | X | 左前进行驶电磁阀电流超弛 | |
| "TRV LEFT BW（左后退行驶" | X | 左后退行驶电磁阀电流超弛 | |
| "TRV RIGHT FW（右前进行驶）" | X | 右前进行驶电磁阀电流超弛 | |
| "TRV RIGHT BW（右后退行驶）" | X | 右后退行驶电磁阀电流超弛 | |
| "BM LOWERING CHECK（动臂下降单向阀）" | X | 动臂下降单向阀/调节阀电磁阀电流超弛 | |
| "ST LOWERING CHECK（斗杆下降单向阀）" | X | 斗杆下降单向阀/调节阀电磁阀电流超弛 | |
| "ATCH EXTEND（附件伸出）" | X | 附件伸出/顺时针电磁阀电流超弛 | |
| "ATCH RETRACT（附件回缩）" | X | 附件回缩/逆时针电磁阀电流超弛 | |
| "MID CURCIT EXTEND（MID 回路伸出）" | X | 中压回路 1-A 电磁阀电流超弛 | |
| "MID CURCIT RETRACT（MID 回路回缩）" | X | 中压回路 1-B 电磁阀电流超弛 | |
| "POWER SHIFT PRES（动力换档压力）" | X | 机具泵动力换档压力电磁阀电流超弛 | |
| "SWING PUMP SWASH（回转泵倾斜）" | X | 斜盘电磁阀电流超弛 | |
Caterpillar Information System:
C7 Engines for Caterpillar Built Machines Unit Injector Hydraulic Pump - Install
345C Material Handler Hydraulic System Generator Set Control
C7 Engines for Caterpillar Built Machines Unit Injector Hydraulic Pump - Remove
365C and 385C Excavators and 365C MHPU and 385C MHPU Mobile Hydraulic Power Units Machine Electronic Control System MID 039 - CID 1148 - FMI 06
365C and 385C Excavators and 365C MHPU and 385C MHPU Mobile Hydraulic Power Units Machine Electronic Control System MID 039 - CID 1147 - FMI 06
C7 Engines for Caterpillar Built Machines Fuel Filter Base - Remove and Install
325C Excavator Joystick Controls Alternate Patterns - If Equipped
D Series Excavator Monitoring System Device Test Mode
D Series Excavator Monitoring System System Schematic
325C LCR Excavator Machine Systems Electronic Control (Heater and Air Conditioner) - Remove and Install
345C Excavator and 345C Material Handler Machine System Specifications Stick - 7.4 m (24.28 ft)
302.5C Mini Hydraulic Excavator Machine System Specifications Swivel
C7 Engines for Caterpillar Built Machines Turbocharger - Remove
C7 Engines for Caterpillar Built Machines Turbocharger - Install
2006/03/06 The Blade Assembly Has Been Improved on Mini Hydraulic Excavators {6051, 6060}
VVP10, VVP15, VVP25 and VVP45 Vibratory Plate Compactors Safety Messages
D Series Excavator Monitoring System Tool Program Mode
C7 Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install
VVP10, VVP15, VVP25 and VVP45 Vibratory Plate Compactors Approved Machines
M325D Material Handler Machine Systems Stick - Remove
365C and 385C Excavators and 365C MHPU and 385C MHPU Mobile Hydraulic Power Units Machine Electronic Control System MID 039 - CID 0376 - FMI 06
345C Excavator Tool Control System System Identification
C7 Engines for Caterpillar Built Machines Engine Oil Filter Base and Oil Cooler - Remove
345C Material Handler Hydraulic System Specifications