Engine Oil Pan - Install
Installation Procedure
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | - | Guide Studs 1/2 - 13 by 5 inch |
4 |
Note: This procedure can only be performed when the engine is removed from the base.
Show/hide table
| NOTICE |
|---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Clean the gasket surface of the engine oil pan and the cylinder block. Install a new gasket (5) on engine oil pan (4) .
Note: Check the inside of the engine oil pan in order to ensure that all of the Tooling has been removed. Ensure that there is nothing under the suction bell.
Show/hide table
 | |
| Illustration 1 | g00553587 |
- Attach a suitable lifting device to the engine lifting brackets. The weight of the 3608 Engine is approximately 19000 kg (41900 lb). Place the engine on support blocks.
- Move engine oil pan (1) into position under the cylinder block. The weight of the 3608 engine oil pan is approximately 737 kg (1625 lb).
Show/hide table
 | |
| Illustration 2 | g00553586 |
- Install Tooling (A) at each corner of engine oil pan (4) . Use a pallet jack in order to raise engine oil pan (4) into position.
- Install bolts (3) .
Show/hide table
 | |
| Illustration 3 | g00553585 |
Typical Example | |
Show/hide table
 | |
| Illustration 4 | g00553584 |
Typical Example | |
- Put the tube assembly and spacer (1) in position. Install bolts (2) .
Note: Lubricate the O-ring seals with clean engine oil before installation.
- Install the clamps and bolts that hold the tube assembly to engine oil pan (4) .
End By:
- Remove the engine lifting brackets. Refer to Disassembly and Assembly, "Engine Lifting Bracket - Remove and Install".
- Install the prelubrication oil pump. Refer to Disassembly and Assembly, "Prelubrication Oil Pump - Install".
Caterpillar Information System:
3608 Engine Engine Oil Pan - Remove
3612 and 3616 Engines Turbocharger Cartridge - Install
2000/03/01 New Turbochargers Provide Increased Bearing Life {1052}
3612 and 3616 Engines Turbocharger Cartridge - Remove
G3500 Industrial Engines System Overview
3612 and 3616 Engines Turbocharger - Assemble
3612 and 3616 Engines Turbocharger - Disassemble
EMCPII+ for Gas Engines EMCP Electronic Control (Generator Set) - Flash Program
3114, 3116 and 3126 MUI Engine Governors Governor (Types IV and Some III) - Adjust
3512 and 3516 EUI Engines for Caterpillar Built Machines Grounding Practices
3500B and 3500B High Displacement Generator Set Engines Electrical System Operation
Uninterruptible Power Supply (UPS) 250 Component Location
G3500 Industrial Engines Timing Control and Interface Box
G3500 Industrial Engines Interaction of Timing Interface Signals
G3500 Industrial Engines Self-Diagnostics
1999/12/01 An Updated Service Manual Module, SENR6565-02, "Generator Set Load Sensor And Generator Set Load Sharing Module" Is Available {4490}
3500B and 3500 Marine Propulsion Engines with EUI Option Reference Material
G3500 Industrial Engines Electrical Connectors and Functions
1999/12/01 Change to Tightening Procedure for Cylinder Head Bolts in Disassembly and Assembly, SENR1002 {1100}
G3500 Industrial Engines TCM Electronic System Logic
1999/12/01 Correction to Special Instruction, REHS0385-01, "Installation Of The Hydraulic Actuator System (Hydrax)" {1716}
G3500 Industrial Engines Introduction
G3500 Industrial Engines Timing Parameters
G3500 Industrial Engines Digital Diagnostic Tool (DDT)