Shell Assembly - Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A(1) | 9U-7536 | Lift Stand | 1 |
447-0910 | Electric Hydraulic Pump (115 V) | 1 | |
447-0911 | Electric Hydraulic Pump (230 V) | 1 | |
A1 | OR | ||
504-9791 | Lift Gp (60Hz)(2) | 1 | |
504-9793 | Lift Gp (50Hz)(3) | 1 | |
B | 439-3939 | Link Bracket | 4 |
C | 1U-9200 | Lever Puller Hoist | 2 |
Show/hide table
(1) | Use Tooling (A) or (A1) based on requirements. |
(2) | Operating Voltage (480V - 240V) |
(3) | Operating Voltage (400V - 200V) |
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, PERJ1017, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products. Dispose of all fluids according to local regulations and mandates. |
- Attach Tooling (B) to shell assembly (2). Attach a suitable lifting device to shell assembly (2). Use Tooling (C) to balance shell assembly (2).
- Attach Tooling (C) to a suitable lifting device and hydraulic cylinder (3). The weight of shell assembly (2) and hydraulic cylinder (3) is approximately
340 kg (750 lb) .Show/hide tableIllustration 2 g00869247 - Remove pin assembly (4) to disconnect hydraulic cylinder (3) (not shown) from shell assembly (2).
Show/hide table
Illustration 3 g00869261 - Position shell assembly (2) to the grapple. Install pin assembly (6) to attach hydraulic cylinder (3) to the grapple.
- Connect two hose assemblies (7) to hydraulic cylinder (3).
Show/hide table
Illustration 4 g06377475 - Reposition shell assembly (2) to the grapple. Install pin assembly (5) to attach shell assembly (2) to the grapple.
Show/hide table
Illustration 5 g00869273 - Install pin assembly (4) to connect hydraulic cylinder (3) (not shown) to shell assembly (2).
Show/hide table
Illustration 6 g00869199 For Tooling (A) - Remove Tooling (A) to allow the weight of the grapple to rest on shell assembly (2).
Show/hide table
Illustration 7 g06377532 For Tooling (A1) - Remove Tooling (A1) to allow the weight of the grapple to rest on shell assembly (2). Refer to Tool Operating Manual, NEHS1303, "Lift Group (Stand - 25 Ton)" for more information on Tooling (A1).
Show/hide table
Illustration 8 g00869191 - Attach cover assembly (1) to shell assembly (2).
Show/hide table
Illustration 1 | g00869317 |
Caterpillar Information System:
5090B Excavator Boom, Stick and Bucket Operation
365B, 365B Series II, 365BL, 385B and 5090B Excavators Machine Electronic Control System MID 039 - CID 1132 - FMI 13
GH52,GH55,GH60 Hydraulic Excavator Forestry Grapples Gerotor Motor Leakage - Test
303 CR Mini Hydraulic Excavator Hydraulic System Pump Control (Main Hydraulic)
N3 Series Brushless Alternators Regulator - Test
314C CR Excavator Hydraulic System Accumulator (Pilot)
325C Excavator Machine Systems Fuel Tank - Install
385B and 5090B Excavators Excavator Systems Swing Drive - Disassemble
365B, 365B Series II, 365BL, 385B and 5090B Excavators Machine Electronic Control System MID 039 - CID 1131 - FMI 13
385B and 5090B Excavators Excavator Systems Boom Bearings and Seals - Install
303 CR Mini Hydraulic Excavator Work Tool Flow Control
321B LCR Excavator Fuses - Replace
321B LCR Excavator Hydraulic System Oil - Change
365B, 365B Series II, 365BL, 385B and 5090B Excavators Machine Electronic Control System MID 039 - CID 0376 - FMI 05
305 Mini Hydraulic Excavator Machine Systems Accumulator (Hydraulic Pilot) - Remove and Install
314C CR Excavator Hydraulic System Solenoid Valve (Hydraulic Activation)
5110B, 5110B L and 5110B MH Excavator Hydraulic System Pilot Valve (Straight Travel)
308C CR Excavator Hydraulic System Blade Hydraulic System
5090B Excavator Counterweight Removal and Installation
GSH9, GSH15, GSH20 and GSH22 Orange Peel Grapples Hydraulic Cylinder and Bearing - Remove and Install
5090B Excavator Lifting and Tying Down the Machine
321B LCR Excavator Hydraulic System Oil Filter - Replace
5090B Excavator Access Door and Cover Locations
5230B Excavator Machine Electronic Control System MID 039 - CID 0379 - FMI 06