Cylinder Speed - Check
注: 发动机转速和 / 或测试期间所用的机器配置可能对测试结果产生影响。 有关此项测试所用的发动机转速,请参阅测试和调整, "发动机性能 - 测试"。 有关此项测试所用的机器配置,请参阅测试和调整, "操作检查"。
注: 执行操作检查之前,必须根据卸压阀压力技术规范设定卸压阀压力。 请参阅测试和调整, "技术规范"。
- 执行下列步骤,以便测试动臂油缸的工作速度。
- 将机器停放在平地上。
Show/hide table图 1 g00298498
(A) 伸出测试
(B) 收回测试
- 铲斗应空载。
- 将铲斗油缸和斗杆油缸完全收回。
- 将铲斗安置在地面上。 使用秒表测量动臂油缸完全伸出所需的时间。
- 使动臂油缸处于完全伸出的位置。 使用秒表测量铲斗与地面接触所需的时间。
- 有关动臂油缸的工作速度,请参阅表 1中的规格。
- 执行下列步骤,以便测试斗杆油缸的工作速度。
- 将机器停放在平地上。
Show/hide table图 2 g00298558
(A) 伸出测试
(B) 收回测试
- 铲斗应空载。
- 使动臂的上表面处于与地面平行的位置。
- 将铲斗油缸完全伸出。
- 将斗杆油缸收回。 使用秒表测量斗杆油缸完全伸出所需的时间。
- 将斗杆油缸伸出。 使用秒表测量斗杆油缸完全收回所需的时间。
- 有关斗杆油缸的工作速度,请参阅表 1 中的技术规范。
- 执行下列步骤,以便测试铲斗油缸的工作速度。
- 将机器停放在平地上。
Show/hide table图 3 g00298598
(A) 伸出测试
(B) 收回测试
- 铲斗应空载。
- 使动臂的上表面处于与地面平行的位置。
- 使斗杆处于与地面垂直的位置。
- 将铲斗油缸完全回缩。
- 使用秒表测量铲斗油缸完全伸出所需的时间。
- 使铲斗油缸处于完全伸出的位置。 使用秒表测量铲斗油缸完全收回所需的时间。
- 有关铲斗油缸的工作速度,请参阅表 1 中的技术规范。
Show/hide table
油缸工作速度(秒)     | |||
---|---|---|---|
项目     | 新装     | 翻新     | |
动臂     | 伸出     | 3.4 ± 0.5     | 4.0 (1)     |
收回 | 2.6 ± 0.5     | 3.3 (1)     | |
斗杆     | 伸出     | 3.4 ± 0.5     | 4.0 (1)     |
收回 | 2.8 ± 0.5     | 3.5 (1)     | |
铲斗     | 伸出     | 4.4 ± 0.5     | 5.0 (1)     |
收回 | 2.5 ± 0.5     | 3.2 (1)     |
Show/hide table
( 1 ) | 最高 |
Caterpillar Information System:
385B Excavator Machine System Specifications Front Lines
330C Excavator Hydraulic System Cylinder Drift - Check - Loaded Bucket
330C Forest Machine Hydraulic System Swing Speed and Swing Drift on a Slope - Check
330C Excavator Hydraulic System Swing Speed and Overswing on Level Ground - Check
330C Excavator Hydraulic System Travel on Level Ground - Test - Optional Test
330C Excavator Hydraulic System Travel on Level Ground - Test
330C Forest Machine Hydraulic System Engine Performance - Test - Engine Speed
330C Forest Machine Machine System Specifications Fuel Tank
330C Excavator Tool Control System System 14: Solenoid Valve (Proportional Reducing) - Calibrate - Attachment Control Valve
330C Excavator Hydraulic System Operational Checks
330C Forest Machine Hydraulic System Main Hydraulic Pump Air - Purge
5230B Excavator Machine Electronic Control System Solenoid Valves
330C Excavator Tool Control System System 14: Relief Valve (Line) - Test and Adjust - Auxiliary Control Valve
330C Forest Machine Hydraulic System Fan Motor Speed (Hydraulic Oil Cooler) - Test and Adjust
330C Excavator Hydraulic System Fan Motor Speed (Hydraulic Oil Cooler) - Test and Adjust
303 CR Mini Hydraulic Excavator Alternate Exit
330C Excavator Hydraulic System Relief Valve (Main) - Test and Adjust
330C Excavator Hydraulic System Relief Valve (Line) - Test and Adjust
330C Forest Machine Hydraulic System Relief Valve (Swing) - Test and Adjust
330C Forest Machine Hydraulic System Relief Valve (Crossover) - Test and Adjust
330C Forest Machine Hydraulic System Fan Motor (Hydraulic Oil Cooler) - Test - Measurement of Case Drain Oil
2001/11/26 Correction to Systems Operation, Testing and Adjusting , " Pump Control (Negative Flow) - Test" {5070}
330C Excavator Hydraulic System Fan Motor (Hydraulic Oil Cooler) - Test - Measurement of Case Drain Oil
330C Excavator Tool Control System System 14: Relief Valve (Line) - Test and Adjust - Number 1 Relief Valve and Number 2 Relief Valve