Fan Motor Speed (Hydraulic Oil Cooler) - Test and Adjust
Show/hide table
所需工具     | ||
---|---|---|
零件号     | 说明     | 数量     |
9U-7400     | 多用转速表工具总成     | 1     |
Show/hide table
图 1 | g00846010 |
发动机室(后) (2) 输出管路 (3) 连接至安全阀的管路(风扇泵) (33) 风扇泵 |
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修产品时,务必留心,确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上液体的工具及用品,参考专门出版物, NENG2500, "卡特彼勒工具和修理车间设备指南"。 按照当地法规和指令处置所有液体。 |
测试
- 将机器停放在水平地面上。
- 关闭发动机。
- 释放液压系统压力。 请参阅测试和调整, "液压系统压力 - 释放"。
- 将 9U-7400 多用转速表工具总成 安装在液压机油冷却器的风扇上。
- 起动发动机。
- 将机器控制装置置于以下设定:AEC 开关关闭 和 发动机转速刻度盘 10。
参考有关发动机转速设置,请参阅测试和调整, "发动机性能 - 测试"。
- 将液压油温度提高至 55°± 5°C (131°± 9°F)。
- 读取风扇转速。 参考图表2 以获得正确的转速。
Show/hide table
表 2 风扇转速     1200 ± 10 rpm (1)     1340 ± 10 rpm (2)     Show/hide table( 1 ) 标准配置 ( 2 ) 高温环境配置
- 如果风扇转速不在规格内,调整风扇泵的安全阀。
调整
- 为了调整风扇泵的安全阀压力设置,松开锁紧螺母 (36) 并转动调整螺钉 (37) 。
注: 把调整螺钉 (37) 顺时针方向转动,以提高压力。 逆时针转动调整螺钉 (37) 可减小压力。
注: 转动安全阀四分之一圈可改变压力约 3300 kPa (480 psi)。
注: 压力升高时,务必进行最终压力调整。
Show/hide table
图 2 | g00846018 |
泵室 (34) 测压口 (35) 安全阀(风扇泵) (36) 锁紧螺母 (37) 调整螺钉 |
- 将安全阀压力调整至表 3 中的规格。
注: 为了避免液压部件损坏,在表 3 中的规格内调整风扇转速。
Show/hide table表 3 风扇转速     安全阀压力     1200 ± 10 rpm (1)    
8800 kPa (1275 psi)    1340 ± 10 rpm (2)    
11100 kPa (1610 psi)    Show/hide table( 1 ) 标准配置 ( 2 ) 高温环境配置
- 拧紧锁紧螺母 (36) 至扭矩为 10 ± 1 N·m (7 ± 0.5 lb ft)。
Caterpillar Information System:
330C Excavator Tool Control System System 14: Relief Valve (Line) - Test and Adjust - Auxiliary Control Valve
330C Excavator Hydraulic System Cylinder Speed - Check
385B Excavator Machine System Specifications Front Lines
330C Excavator Hydraulic System Cylinder Drift - Check - Loaded Bucket
330C Forest Machine Hydraulic System Swing Speed and Swing Drift on a Slope - Check
330C Excavator Hydraulic System Swing Speed and Overswing on Level Ground - Check
330C Excavator Hydraulic System Travel on Level Ground - Test - Optional Test
330C Excavator Hydraulic System Travel on Level Ground - Test
330C Forest Machine Hydraulic System Engine Performance - Test - Engine Speed
330C Forest Machine Machine System Specifications Fuel Tank
330C Excavator Tool Control System System 14: Solenoid Valve (Proportional Reducing) - Calibrate - Attachment Control Valve
330C Excavator Hydraulic System Operational Checks
330C Excavator Hydraulic System Fan Motor Speed (Hydraulic Oil Cooler) - Test and Adjust
303 CR Mini Hydraulic Excavator Alternate Exit
330C Excavator Hydraulic System Relief Valve (Main) - Test and Adjust
330C Excavator Hydraulic System Relief Valve (Line) - Test and Adjust
330C Forest Machine Hydraulic System Relief Valve (Swing) - Test and Adjust
330C Forest Machine Hydraulic System Relief Valve (Crossover) - Test and Adjust
330C Forest Machine Hydraulic System Fan Motor (Hydraulic Oil Cooler) - Test - Measurement of Case Drain Oil
2001/11/26 Correction to Systems Operation, Testing and Adjusting , " Pump Control (Negative Flow) - Test" {5070}
330C Excavator Hydraulic System Fan Motor (Hydraulic Oil Cooler) - Test - Measurement of Case Drain Oil
330C Excavator Tool Control System System 14: Relief Valve (Line) - Test and Adjust - Number 1 Relief Valve and Number 2 Relief Valve
330C Excavator Hydraulic System Specifications
Programming the Tool Control System in the Electronic Control Monitor for Using a Hammer on the Auxiliary Hydraulic Control System 3 (NACD Hammer){7490} Programming the Tool Control System in the Electronic Control Monitor for Using a Hammer on the Auxiliary Hydraulic Control System 3 (NACD Hammer){7490}