SR17, SR18, SR21, SR318 and SR321 Snowblowers Caterpillar


Cutting Edge - Replace

Usage:

SR321 BLZ


注意

不要将除雪机完全撤回到 904B 小型轮式装载机 上。否则会损坏抛送槽。


  • 把起吊臂完全降下。 向后倾斜除雪机,以达到铲刀刃。

    1. 在升高了的除雪机铲刀下放置垫块。



      图 1g00933556

    1. 卸下螺母和螺栓。卸下铲刀刃。

    1. 擦净安装表面。

    1. 安装新的铲刀刃。

    1. 安装螺栓。 用规定的扭矩拧紧螺栓。 请参阅扭矩技术规格, SENR3130。

    1. 工作数小时后,检查螺栓的扭矩是否正确。
  • Caterpillar Information System:

    CVP16, CVP40, CVP75 and CVP110 Vibratory Plate Compactors Lifting and Tying Down
    SR17, SR18, SR21, SR318 and SR321 Snowblowers Discharge Chute Chain - Adjust/Replace
    SR17, SR18, SR21, SR318 and SR321 Snowblowers Chain - Lubricate
    CVP16, CVP40, CVP75 and CVP110 Vibratory Plate Compactors Transport Position
    CVP16, CVP40, CVP75 and CVP110 Vibratory Plate Compactors Reference Material
    325C Excavator Machine System Specifications Upper Frame
    SR17, SR18, SR21, SR318 and SR321 Snowblowers Operation
    305 CR Mini Hydraulic Excavator Cooling System Pressure Cap - Clean/Replace
    G3500B Engines Compression
    322C Excavator Machine System Specifications Fuel Tank
    BH27, BH30 and BH30 W Skid Steer Loader Backhoes Boom Cylinder - Remove and Install
    5130B Excavator Bearing (Swing Drive) - Lubricate
    320C U Excavator Lifting Capacities
    3176C, 3196 and 3406E Engines for Caterpillar Built Machines Digital Sensor Supply Circuit - Test
    325C Excavator Machine System Specifications Auxiliary Hydraulic Lines - Stick 2500 mm (98 inch)
    325C Excavator Machine System Specifications Auxiliary Hydraulic Lines - Stick 2600 mm (102 inch)
    325C Excavator Machine System Specifications Auxiliary Hydraulic Lines - Stick 3200 mm (126 inch)
    SR17, SR18, SR21, SR318 and SR321 Snowblowers Reference Material
    325C Excavator Machine System Specifications Auxiliary Hydraulic Lines - Stick 2000 mm (79 inch)
    BB121 and BB124 AccuGrade Box Blade Storage
    325C Excavator Machine System Specifications Auxiliary Hydraulic Lines - Stick 2000 mm (79 inch)
    W345B Series II Excavator Hydraulic System Specifications
    325C LCR Excavator Machine System Specifications Auxiliary Hydraulic Lines - Stick 3200 mm (126 inch)
    2002/04/01 New Seals in the Final Drives Reduce Oil Leaks and the Entry of Debris {7555}
    Back to top
    The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
    CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.