Programmable Parameters
Understanding Programmable Engine RPM Limits
Note: Many programmable parameters affect the engine operation. These parameters may be changed with the Caterpillar Electronic Technician (ET). The parameters are stored in the ECM. The parameters are not stored in the personality module. Any parameter can be read. However, passwords protect parameters from unauthorized changes. Refer to Troubleshooting, "Customer Specified Parameters Table" for more information.
There are four programmable engine rpm limits that are available.
Note: The Top Engine Limit is not a programmable feature on the October 2001 and newer software for the Medium-Duty Engines and the January 2002 and newer software for the Heavy-Duty Engines..
Top Engine Limit (TEL) - The TEL is used while the vehicle is being driven on the road. The TEL determines the maximum rpm when the PTO On/Off Switch is in the OFF position.
Idle RPM Limit - The "Idle RPM Limit" is the maximum of the engine rpm limit if the engine rpm is established by using the Cruise Control On/Off switch and the Cruise Control Set/Resume switch. The programmable range of the "Idle RPM Limit" is from 700 rpm to the TEL in one rpm increments. The minimum programmable Idle RPM Limit is determined by the programmed Low Idle RPM. The maximum programmable "Idle RPM Limit" is limited by the Top Engine Limit.
PTO Top Engine Limit - The "PTO Top Engine Limit" is the maximum engine rpm limit when the PTO On/Off switch is ON. The "PTO Top Engine Limit" has a programmable range from 700 rpm to the TEL in one rpm increments. The minimum programmable "PTO Top Engine Limit" is actually determined by the programmed Low Idle rpm. The maximum programmable "PTO Top Engine Limit" is the TEL.
Fast Idle Engine RPM Limit - The "Fast Idle RPM Limit" is the maximum rpm set speed that uses the Fast Idle Enable switch. The programmable range is 700 rpm to the TEL in one rpm increments. The operator can override the programmed "Fast Idle RPM". Depress the accelerator pedal and toggle the Fast Idle Enable switch when the engine is at the desired rpm. This rpm would then be the "Fast Idle RPM" until the engine is shut down.
Note: The Fast Idle Option is not available on the C-10, C11, C-12, C13, 3406E, C15, C-15, C-16, and C-18 engines.
Available Ranges, Options, and Default Settings for the Programmable Parameters
Note: Table 1 refers to the C-10, C11, C-12, C13, 3406E, C15, C-15, C-16, and C-18.
Show/hide table
| Table for Customer Specified Parameters | ||
|---|---|---|
| "Parameter" | Available Range or Options | Default |
| "Selected Engine Rating" | ||
| "Rating Number" | Dependent on engine power | |
| "Multitorque Ratio" | Unavailable (Standard Ratings) "MT-A" "MT-B" "MT-C" |
Unavailable (Standard Ratings) "MT-A" (Multitorque Ratings) |
| "ECM Identification Parameters" | ||
| "Vehicle ID" | 17 Digits Available characters are dependent on the service tools. |
all zeroes |
| "Security Access Parameters" | ||
| "ECM Wireless Communication Enable" | "No" "Yes" |
"No" |
| "Vehicle Speed Parameters" | ||
| "Vehicle Speed Calibration" | 2485 to 93226 PPKM (4000 to 150000 PPM) |
Not Programmed |
| "Vehicle Speed Cal (J1939 - Trans)" | 0 to 43000 revolutions per km (0 to 65000 revolutions per mile) | Not Programmed |
| "Vehicle Speed Cal (J1939 - ABS)" | 0 to 6.550 | Not Programmed |
| "Vehicle Speed Limit" | 48 to 204 km/h (30 to 127 mph) |
204 km/h (127 mph) |
| "VSL Protection" | 1000 to TEL rpm | TEL rpm |
| "Tachometer Calibration" | 12.0 to 500.0 pulses per revolution | 113.0 pulses per revolution |
| "Soft Vehicle Speed Limit" | "No" "Yes" |
"No" |
| "Two Speed Axle - Low Speed Range Axle Ratio" | 1.00 to 19.99 | 1.00 |
| "Nominal Axle Ratio - High Speed Range Axle Ratio" | 1.0 to 9.99 | 1.00 |
| "Cruise Control Parameters" | ||
| "Low Cruise Control Speed Set Limit" | 24 to 204 km/h (15 to 127 mph) |
204 km/h (127 mph) |
| "High Cruise Control Speed Set Limit" | 48 to 204 km/h (30 to 127 mph) |
204 km/h (127 mph) |
| "Engine Retarder Mode" | "Coast" "Latch" "Manual" |
"Manual" |
| "Engine Retarder Minimum VSL Type" | "Hard Limit" "Soft Limit" |
"Hard Limit" |
| "Engine Retarder Minimum Vehicle Speed" | 0 to 204 km/h (0 to 127 mph) |
0 km/h (0 mph) |
| "Auto Retarder in Cruise (0 = Off)" | 0 to 16 km/h (0 to 10 mph) |
0 km/h (0 mph) |
| "Auto Retarder in Cruise Increment" | 0 to 8 km/h (0 to 5 mph) |
3 km/h (2 mph) |
| "Cruise/Idle/PTO Switch Configuration" | "Set/Accel-Res/Decel" "Set/Decel-Res/Accel" |
"Set/Accel-Res/Decel" |
| "Soft Cruise Control" | "No" "Yes" |
"Yes" |
| "Adaptive Cruise Control Enable" | "Disabled" "Enabled" |
"Disabled" |
| "Idle Parameters" | ||
| "Idle Vehicle Speed Limit" | 2 to 24 km/h (1 to 15 mph) |
2 km/h (1 mph) |
| "Idle RPM Limit" | Low Idle to 2120 rpm | 2120 rpm |
| "Idle/PTO RPM Ramp Rate" | 5 to 1000 rpm/sec | 50 rpm/sec |
| "Idle/PTO Bump RPM" | 5 to 500 rpm | 20 rpm |
| "Dedicated PTO Parameters" | ||
| "PTO Configuration" | "Cab Switches" "Off" "Remote Switches" "Remote Throttle" |
"Off" |
| "PTO Top Engine Limit" | Low Idle to 2120 rpm | 2120 rpm |
| "PTO Engine RPM Set Speed (0 = Off)" | Low Idle to PTO TEL rpm | 0 |
| "PTO Engine RPM Set Speed A" | Low Idle to PTO TEL rpm | 0 |
| "PTO Engine RPM Set Speed B" | Low Idle to PTO TEL rpm | 0 |
| "PTO to Set Speed" | "No" "Yes" |
"No" |
| "Maximum PTO Enable Speed" | Low Idle to PTO TEL rpm | PTO TEL rpm |
| "PTO Cab Controls RPM Limit" | "Low Idle" "TEL" "PTO TEL" |
"TEL" |
| "PTO Kickout Vehicle Speed Limit" | 2 to 204 km/h (1 to 127 mph) |
2 km/h (1 mph) |
| "Max PTO Vehicle Speed" | 24 to 204 km/h (15 to 127 mph) |
204 km/h (127 mph) |
| "Torque Limit" | 270 N·m (200 lb ft) to Rated Torque | 3400 N·m (2500 lb ft) |
| "PTO Shutdown Time (0 = Off)" | 3 to 1440 minutes | 0 |
| "PTO Shutdown Timer Maximum RPM" | 600 to PTO TEL rpm | PTO TEL rpm |
| "PTO Activates Cooling Fan" | "Continuous" "Normal" |
"Normal" |
| "Engine/Gear Parameters" | ||
| "Lower Gears Engine RPM Limit" | 1100 to TEL rpm | TEL rpm |
| "Lower Gears Turn Off Speed" | 5 to 48 km/h (3 to 30 mph) |
5 km/h (3 mph) |
| "Intermediate Gears Engine RPM Limit" | 1100 to TEL rpm | TEL rpm |
| "Intermediate Gears Turn Off Speed" | 8 to 80 km/h (5 to 50 mph) |
8 km/h (5 mph) |
| "Gear Down Protection RPM Limit" | 1300 to TEL rpm | TEL rpm |
| "Gear Down Protection Turn On Speed" | 48 to 204 km/h (30 to 127 mph) |
204 km/h (127 mph) |
| "Low Idle Engine RPM" | 600 to 750 rpm | 600 rpm |
| "Transmission Style" | "Automatic Option 1" "Automatic Option 2" "Automatic Option 3" "Automatic Option 4" "Eaton Top 2" "Manual Option 1" |
"Manual Option 1" |
| "Eaton Top 2 Override with Cruise Switch" | "No" "Yes" |
"No" |
| "Top Gear Ratio" | 0.000 to 3.750 | 0.000 |
| "Top Gear Minus One Ratio" | 0.000 to 3.750 | 0.000 |
| "Top Gear Minus Two Ratio" | 0.000 to 3.750 | 0.000 |
| "Governor Type" | "Full Range" "Min/Max" "Min/Max with Speed Control" |
"Full Range" |
| "Timer Parameters" | ||
| "Idle Shutdown Time (0 = Off)" | 3 to 1440 minutes | 0 minutes |
| "Idle Shutdown Timer Maximum RPM" | Low Idle to 2120 rpm | 2120 rpm |
| "Allow Idle Shutdown Override" | "J1587 Outside Temp Based" "No" "Outside Temperature Based" "Yes" |
"Yes" |
| "Minimum Idle Shutdown Outside Temp" | −40° to 49°C (−40° to 120°F) |
49 °C (120 °F) |
| "Maximum Idle Shutdown Outside Temp" | −40° to 49°C (−40° to 120°F) |
49 °C (120 °F) |
| "A/C Switch Fan On-Time (0 = Off)" | 1 to 600 seconds | 0 seconds |
| "Fan with Engine Retarder in High Mode" | "No" "Yes" |
"No" |
| "Engine Retarder Delay" | 0.0 to 3.0 seconds | 0.0 seconds |
| "Smart Idle Parameters" | ||
| "Battery Monitor and Engine Control Voltage" | 0 to 25.5 volts | 0.0 volts |
| "Engine Monitoring Parameters" | ||
| "Engine Monitoring Mode" | "Derate" "Shutdown" "Warning" |
"Warning" |
| "Engine Monitoring Lamps" | "Option 1" "Warning Lamp" |
"Warning Lamp" |
| "Coolant Level Sensor" | "2-wire Float Sensor" "4-pin" "No" |
"No" |
| "Engine Coolant Temperature Derate Enable Status" This parameter is not supported in DEC 03 and newer software. |
"Disabled" "Enabled" |
"Disabled" |
| "Maintenance Parameters" | ||
| "Maintenance Indicator Mode" | "Automatic Distance" "Automatic Hours" "Manual Distance" "Manual Hours" "Off" |
"Off" |
| "PM 1 Interval (Manual Maintenance Indicator Mode)" | 8050 to 56325 km (5000 to 35000 miles) 100 to 750 hours |
24140 km (15000 miles) 250 hours |
| "Engine Oil Capacity" | 19 to 57 L (20 to 60 qt) |
C11, C13: 34 L (36 qt) C15: 38 L (40 qt) |
| "Trip Parameters" | ||
| "Fuel Correction Factor" | −63.5 to 63.5 % | 0 % |
| "Dash-Change Fuel Correction Factor" | "No" "Yes" |
"No" |
| "Dash-PM 1 Reset" | "No" "Yes" |
"No" |
| "Dash-Fleet Trip Reset" | "No" "Yes" |
"No" |
| "Dash-State Selection" | "No" "Yes" |
"Yes" |
| "Theft Deterrent System Control" | "Auto-Enable" "No" "Yes" |
"No" |
| "Theft Deterrent Password" | Four Characters | 0000 |
| "Quick Stop Rate" | 5 to 24 km/h per sec (3 to 15 mph per sec) | 0 km/h per sec (0 mph per sec) |
| "Vehicle Overspeed Threshold" | 48 to 204 km/h (30 to 127 mph) |
204 km/h (127 mph) |
| "Vehicle Activity Report Parameters" | ||
| "Minimum Idle Time (0 = Off)" | 0 to 1440 minutes | 0 minutes |
| "Driver Reward" | ||
| "Driver Reward Enable" | "Disabled" "Enabled" |
"Enabled" |
| "Input Selections" | ||
| "Fan Override Switch" | "J1/P1:46" "J1/P1:47" "J1/P1:6" "J1/P1:7" "J1939 - Body Controller" "J1939 - Cab Controller" "J1939 - Instrument Cluster" "None" |
"None" |
| "Transmission Neutral Switch" | "None" "J1939" "J1/P1:62" |
"None" |
| "Ignore Brake/Clutch Switch" | "J1/P1:47" "None" |
"None" |
| "Torque Limit Switch" | "J1/P1:7" "None" |
"None" |
| "Diagnostic Enable" | "J1/P1:46" "J1939 - Body Controller" "J1939 - Cab Controller" "J1939 - Instrument Cluster" "None" |
"None" |
| "PTO On/Off Switch" | "J1/P1:56" "J1939 - Cab Controller" "J1939 - Body Controller" "J1939 - Instrument Cluster" |
"J1/P1:56" |
| "Remote PTO Set Switch" | "J1/P1:58" "J1939 - Body Controller" "J1939 - Cab Controller" "J1939 - Instrument Cluster" "None" |
"J1/P1:58" |
| "Remote PTO Resume Switch" | "J1/P1:60" "J1939 - Body Controller" "J1939 - Cab Controller" "J1939 - Instrument Cluster" "None" |
"J1/P1:60" |
| "PTO Engine RPM Set Speed Input A" | "J1/P1:46" "J1/P1:58" "J1/P1:6" "J1/P1:60" "J1939 - Body Controller" "J1939 - Cab Controller" "J1939 - Instrument Cluster" "None" |
"None" |
| "PTO Engine RPM Set Speed Input B" | "J1/P1:46" "J1/P1:58" "J1/P1:6" "J1/P1:60" "None" |
"None" |
| "Starting Aid On/Off Switch" | "J1/P1:46" "J1/P1:47" "J1/P1:6" "J1/P1:7" "None" |
"None" |
| "Two-Speed Axle Switch" | "J1/P1:6" "J1939 - Body Controller" "J1939 - Cab Controller" "J1939 - Instrument Cluster" "None" |
"None" |
| "Cruise Control On/Off Switch" | "J1/P1:59" "J1939 - Body Controller" "J1939 - Cab Controller" "J1939 - Instrument Cluster" |
"J1/P1:59" |
| "Cruise Control Set/Resume/Accel/Decel Switch" | "J1/P1:35 & 44" "J1939 - Body Controller" "J1939 - Cab Controller" "J1939 - Instrument Cluster" |
"J1/P1:35 & 44" |
| "Cruise Control Pause Switch" | "J1939 - Body Controller" "J1939 - Cab Controller" "J1939 - Instrument Cluster" "None" |
"None" |
| "Clutch Pedal Position Switch" | "J1/P1:22" "J1939 - Body Controller" "J1939 - Cab Controller" "J1939 - Instrument Cluster" |
"J1/P1:22" |
| "Retarder Off/Low/Medium/High Switch" | J1/P1:23 & 40 "J1939 - Body Controller" "J1939 - Cab Controller" "J1939 - Instrument Cluster" |
J1/P1:23 & 40 |
| "Service Brake Pedal Position Switch #1" | "J1/P1:45" "J1939 - Body Controller" "J1939 - Cab Controller" "J1939 - Instrument Cluster" |
"J1/P1:45" |
| "Accelerator Pedal Position" | "J1/P1:66" | "J1/P1:66" |
| "Vehicle Speed Input" | "J1/P1:32 & 33" "J1939 − ABS" "J1939 − Trans" |
"J1/P1:32 & 33" |
| "Output Selections" | ||
| "Engine Running Output" | "J1/P1:10" "J1/P1:12" "J1/P1:13" "None" |
"None" |
| "Engine Shutdown Output" | "J1/P1:10" "J1/P1:12" "J1/P1:13" "None" |
"None" |
| "Auxiliary Brake" | "J1/P1:12" "None" |
"None" |
| "Starting Aid Output" | "J1/P1:10" "J1/P1:12" "J1/P1:13" "None" |
"None" |
| "Fan Control Type" | "None" "On/Off PWM" "On/Off DC" "Three-Speed Fan PWM" "Three-Speed Fan DC" "Variable Speed Fan Option S" |
"None" |
| "PTO Active Output" | "J1/P1:19" "None" |
"None" |
| "Customer Passwords" | ||
| "Customer Password #1" | 8 Digits Available characters are dependent on the service tools. |
Not Programmed |
| "Customer Password #2" | ||
| "Data Link Parameters" | ||
| "Power Train Data Link" | "J1939" "None" |
"J1939" |
Note: Table 2 refers to the 3126B, 3126E, C7, and C9.
Show/hide table
| Customer Specified Parameters | ||
|---|---|---|
| ECM Parameter | Possible Values | Default Value |
| Engine Rating Parameter | ||
| "Rating Number" | Dependent on engine power | - |
| Vehicle ID | ||
| "Vehicle ID" | 17 Digits Available characters are dependent on the service tool that is used. |
Not Programmed |
| +Truck Manufacturer | ||
| "Truck Manufacturer" ( C7 Engines) |
GM Other |
Not Programmed |
| "Truck Model Type" ( C7 Engines) |
GM 530/540 GMT-560 |
GM 530/540 |
| Vehicle Speed Parameters | ||
| "Vehicle Speed Calibration" | GM: 2485 to 238080 PPKM (4000 to 384000 PPM) Other: 2485 to 238080 PPKM (4000 to 384000 PPM) |
19884 PPKM (32000 PPM) Not Programmed |
| "Vehicle Speed CAL (J1939-Trans)" | 0 to 43000 rev per km (0 to 65000 rev per mile) | Not Programmed |
| "Vehicle Speed CAL (J1939-ABS)" | 0 to 6.550 | Not Programmed |
| "Vehicle Speed Limit (VSL)" | GM: 48 to 121 km/h (30 to 75 mph) Other: 48 to 204 km/h (30 to 127 mph) |
GM: 121 km/h (75 mph) Other: 204 km/h (127 mph) |
| "VSL Protection" | 1700 to TEL rpm | TEL rpm |
| "Tachometer Calibration" | (2.0 to 500.0 PPR) | GMT 530/540: (17.5 PPR) GMT-560: (2.0 PPR) Other: (134.0 PPR) |
| "Soft Vehicle Speed Limit" | Yes No |
No |
| "Low Speed Range Axle Ratio" | 0.00 to 19.99 | 0.00 |
| "High Speed Range Axle Ratio" | 0.0 to 9.99 | 0.00 |
| Cruise Control Parameters | ||
| "Low Cruise Control Speed Set Limit" | GM: 40 to 121 km/h (25 to 75 mph) Other: 24 to 204 km/h (15 to 127 mph) |
GM: 40 km/h (25 mph) Other: 204 km/h (127 mph) |
| "High Cruise Control Speed Set Limit" | GM: 48 to 121 km/h (30 to 75 mph) Other: 32 to 204 km/h (20 to 127 mph) |
GM: 121 km/h (75 mph) Other: 204 km/h (127 mph) |
| "Engine Brake Mode" | Coast Latch Manual |
Manual |
| "Cruise/Idle/PTO Switch Configuration" | Set/Decel-Res/Accel Set/Accel-Res/Decel |
GM: Set/Decel Other: Set/Accel |
| "Soft Cruise Control" | Yes No |
GM: No Other: Yes |
| "Auto Retarder in Cruise (0 = Off)" | 5 to 16 km/h (3 to 10 mph) |
0 km/h (0 mph) |
| Idle Parameters | ||
| "Idle Vehicle Speed Limit" | 2 to 24 km/h (1 to 15 mph) |
2 km/h (1 mph) |
| "Idle RPM Limit" | 700 to TEL rpm | TEL rpm |
| "Idle/PTO RPM Ramp Rate" | (5 to 1000 rpm/sec) | (50 rpm/sec) |
| "Idle/PTO Bump RPM" | 5 to 500 rpm | 20 rpm |
| "Fast Idle RPM 1" | 700 to TEL rpm | 1000 rpm |
| "Fast Idle RPM 2" | 700 to TEL rpm | 0 rpm |
| "Warm up Mode Idle Speed" | 700 to 1400 rpm | 1000 rpm |
| PTO Parameters | ||
| "PTO Configuration" | Off Cab Switches Remote Switches Remote Throttle |
Off |
| "PTO Top Engine Limit" | 700 to TEL rpm | TEL rpm |
| "PTO Engine RPM Set Speed" | Low idle to PTO TEL rpm | 0 rpm |
| "PTO Engine RPM Set Speed A" | Low Idle to PTO TEL rpm | 0 rpm |
| "PTO Engine RPM Set Speed B" | Low Idle to PTO TEL rpm | 0 rpm |
| "PTO to Set Speed" | Yes No |
No |
| "Maximum PTO Enable Speed" | 700 to TEL rpm | TEL rpm |
| "PTO Cab Controls RPM Limit" | Low idle rpm TEL rpm PTO TEL rpm |
TEL rpm |
| "PTO Kickout Vehicle Speed Limit" | 2 to 204 km/h (1 to 127 mph) |
2 km/h (1 mph) |
| Maximum PTO Vehicle Speed | 5 to 204 km/h (3 to 127 mph) |
204 km/h (127 mph) |
| "Torque Limit" | 135 N·m (100 lb ft) to Rated Torque | 2712 N·m (2000 lb ft) |
| "PTO Shutdown Time" | 3 to 1440 minutes | 0 minutes |
| "PTO Activates Cooling Fan" | Normal Continuous |
Normal |
| Exhaust Brake Options | ||
| "Exhaust Brake Warm Up Enable" | None Warm Up Only Exhaust Brake Only Exhaust Brake & Warm Up |
GM 530/540: Exhaust Brake Only GMT-560: None Other: Exhaust Brake Only |
| Engine/Gear Speed Limit Parameters | ||
| "Lower Gears Engine RPM Limit" | 1500 to TEL rpm | TEL rpm |
| "Lower Gears Turn Off Speed" | 2 to 24 km/h (1 to 15 mph) |
2 km/h (1 mph) |
| "Intermediate Gears Engine RPM Limit" | 1500 to TEL rpm | TEL rpm |
| "Intermediate Gears Turn Off Speed" | 16 to 80 km/h (10 to 50 mph) |
16 km/h (10 mph) |
| "Gear Down Protection RPM Limit" | 1700 to TEL rpm | TEL rpm |
| "Gear Down Protection Turn On Speed" | GM: 48 to 121 km/h (30 to 75 mph) Other: 48 to 204 km/h (30 to 127 mph) |
GM: 121 km/h (75 mph) Other: 204 km/h (127 mph) |
| "Top Engine Limit (TEL)" | Dependent on the engine and the rating | Dependent on the engine rating |
| "Low Idle Engine RPM" | 700 to 800 rpm | 700 rpm |
| "Transmission Style" | GM only Universal Manual Option 1 GM only Manual Option 2 Automatic Option 1 Automatic Option 2 Automatic Option 3 Automatic Option 4 AT/MT/HT Option 1 AT/MT/HT Option 2 AT/MT/HT Option 3 AT/MT/HT Option 4 |
GM 530/540: Universal GMT-560: Manual Option 2 Other: Manual Option 1 |
| "AT/MT/HT Part Throttle Shift Speed" | Low (80% Enable/65% Disabel) Medium (70% Enable/55% Disable) High (60% Enable/45% Disable) |
High (60% Enable/45% Disable) |
| "Starting Aid Output" | Automatic Off |
Off |
| "Governor Type" | Min/Max Min/Max with Speed Control Full Range |
Full Range |
| Smart Idle Parameters | ||
| "Battery Monitor & Engine Control Voltage" | 0 to 25.5 Volts | GM 530/540: 0 Volts GMT-560: 11.5 Volts Other: 0 Volts |
| "Battery Monitor Low Idle Speed Monitor" | 700 to TEL rpm | 1000 rpm |
| Timer Parameters | ||
| "Idle Shutdown Time" | 3 to 1440 minutes | 0 minutes |
| "Allow Idle Shutdown Override" | Yes No |
Yes |
| "A/C Switch Fan-On Time" | 0 to 600 seconds | 0 second |
| "Fan with Engine Brake On" | Yes No |
Yes |
| Engine Monitoring Parameters | ||
| "Engine Monitoring Mode" | Warning Shutdown Derate |
GM 530/540: Warning GMT560: Derate Other: Warning |
| "Engine Monitoring Lamps" (Other & GM 530/540) |
High Coolant Temp Warning Lamp: GM 530/540 only Warning Lamp: Other and GM 530/540 only Option 1: Other only |
GM 530/540: Warning Lamp Other: Warning Lamp |
| "Coolant Level Sensor" | No 4 Pin 2-pin switch: GMT- 560 only 2 Wire Float Sensor: Other only |
Other: No GM 530/540: No GMT- 560: 2-Pin Switch |
| "Engine Oil Pressure Sensor" | Installed Not Installed |
Other: Not Installed GM 530/540: Not Installed GMT- 560: Installed |
| "Oil Level Switch" (GMT-560) |
Installed Not Installed |
GMT-560: Installed |
| Maintenance Parameters | ||
| "Maintenance Indicator Mode" | OFF Manual Distance Manual Hours Automatic Distance Automatic Hours |
Other: Off GM 530/540: Off GMT-560: Automatic Distance |
| "PM 1 Interval (Manual Maintenance Indicator Mode)" | Manual Distance: 8050 to 56325 km (5000 to 35000 miles) Manual Hours: 100 to 750 hours |
Other: 24140 km (15000 miles) GM 530/540: 1900 kilometers (1200 miles) or 250 hours GMT-560: 1900 kilometers (1200 miles) or 250 hours |
| "Engine Oil Capacity" | 19 to 57 L (20 to 60 qt) |
Other: 31 L (33 qt) GM 530/540: 21 L (22 qt) GMT-560: 21 L (22 qt) |
| Trip Parameters | ||
| "Dash - PM 1 Reset" | Yes No |
Other: No GM 530/540: No GMT-560: Yes |
| "Dash - Customer Parameters" | Yes No |
No |
| "Theft Deterrent System Control" | Yes No Auto-Enable |
No |
| "Theft Deterrent Password" | Four Characters Available characters are dependent on the service tool that is used. |
0000 |
| "Quick Stop Rate" | 0 to 205 km/h (0 to 128 mph) per second |
0 km/h (0 mph) per second |
| Input Selections | ||
| "Fan Override Switch" | None J1939 Body Controller J1939 Cab Controller J1939 Instrument Cluster |
None |
| "Transmission Neutral Switch" | J1/P1:62 J1939 |
J1/P1:62 |
| "Exhaust Brake Switch" | None J1/P1:16 J1939 Body Controller J1939 Cab Controller J1939 Instrument Cluster |
None |
| "Ignore Brake/Clutch Switch" | None J1/P1:47 |
None |
| "2-Speed Axle Switch" | None J1/P1:6 |
None |
| "Vehicle Speed Input" | None J1/P1:32 & 33 J1939-ABS J1939-Trans |
J1/P1:32 & 33 |
| "PTO On/Off Switch" | J1/P1:56 J1939 Body Controller J1939 Cab Controller J1939 Instrument Cluster |
J1/P1:56 |
| "Remote PTO Set Switch" | None J1/P1:58 J1939 Body Controller J1939 Cab Controller J1939 Instrument Cluster |
J1/P1:58 |
| "Remote PTO Resume Switch" | None J1/P1:60 J1939 Body Controller J1939 Cab Controller J1939 Instrument Cluster |
J1/P1:60 |
| "PTO Engine Shutdown Switch" | None J1/P1:7 J1/P1:23 |
None |
| "Torque Limit Switch" | None J1/P1:7 J1/P1:23 |
None |
| "PTO Engine RPM Set Speed Input A" | None J1/P1:46 J1939 Body Controller J1939 Cab Controller J1939 Instrument Cluster |
None |
| "PTO Engine RPM Set Speed Input B" | None J1/P1:7 J1/P1:23 |
None |
| "Diagnostic Enable" | None J1/P1:46 J1939 Body Controller J1939 Cab Controller J1939 Instrument Cluster |
None |
| "Cruise Control On/Off Switch" | J1/P1:59 J1939 Body Controller J1939 Cab Controller J1939 Instrument Cluster |
J1/P1:59 |
| "Cruise Control Set/Resume/Accel/Decel Switch" | J1/P1:35 & 44 J1939 Body Controller J1939 Cab Controller J1939 Instrument Cluster |
J1/P1:35 & 44 |
| "Cruise Control Pause Switch" | None J1939 Body Controller J1939 Cab Controller J1939 Instrument Cluster |
None |
| "Clutch Pedal Position Switch" | J1/P1:22 J1939 Body Controller J1939 Cab Controller J1939 Instrument Cluster |
J1/P1:22 |
| "Service Brake Pedal Position Switch #1" | J1/P1:45 J1939 Body Controller J1939 Cab Controller J1939 Instrument Cluster |
J1/P1:45 |
| "Accelerator Pedal Position" | J1/P1:66 | J1/P1:66 |
| "A/C High Pressure Switch" (Other & GM 530/540) |
None J1/P1:41 |
J1/P1:41 GM 530/540: J1/P1:41 |
| "A/C Fan Request Switch" (GM 530/540) |
None J1/P1:41 J1/P1:62 |
GM 530/540: J1/P1:62 |
| Output Selections | ||
| "Fan Control Type" | None On/Off PWM On/Off DC Variable Speed Fan Option S |
None |
| "PTO Active Output Configuration" | None J1/P1:19 |
None |
| "PTO Switch On Lamp" | None J1/P1:30 |
J1/P1:30 |
| Fast Idle Enable Lamp (Other & GMT-560) |
None J1/P1:31 J1/P1:21 |
Other: J1/P1:31 GMT-560: J1/P1:21 |
| "Wait To Start Lamp" (Other) |
None J1/P1:31 J1939 |
None |
| "Engine Running Output" (GMT-560) |
None J1/P1:31 |
GMT-560: J1/P1:31 |
| "Change Oil Lamp" | None J1/P1:30 |
None |
| "Primary Fuel Level Tank Capacity" (GMT-560) |
None 95 L (25 US gal) 130 L (35 US gal) 190 L (50 US gal) |
GMT-560: 190 L (50 US gal) |
| "Secondary Fuel Level Tank Capacity" (GMT-560) |
None 95 L (25 US gal) 130 L (35 US gal) 190 L (50 US gal) |
GMT-560: None |
| Customer Passwords | ||
| "Customer Password #1" | 8 Characters Available characters are dependent on the service tool that is used. |
Not Programmed |
| "Customer Password #2" | 8 Characters Available characters are dependent on the service tool that is used. |
Not Programmed |
| Data Link Parameters | ||
| "Powertrain Data Link" | None J1939 |
Other: None GM 530/540: J1939 GMT-560: J1939 |
Caterpillar Information System:
3054 Truck Engine Crankcase Breather
3500B Engines Turbocharger - Install - Rear Mounted Turbocharger
3512B Marine Auxiliary Engine MID 111 - CID 1215 - FMI 05 Thermocouple #15 open circuit
3054 Truck Engine Water Temperature Regulator Housing
3512B Marine Auxiliary Engine MID 111 - CID 1215 - FMI 04 Thermocouple #15 short to ground
3126B and 3126E On-highway Engines Belt Tightener - Assemble
3512B Marine Auxiliary Engine MID 111 - CID 1214 - FMI 05 Thermocouple #14 open circuit
3512B Marine Auxiliary Engine MID 111 - CID 1214 - FMI 04 Thermocouple #14 short to ground
3512B Marine Auxiliary Engine MID 111 - CID 1213 - FMI 05 Thermocouple #13 open circuit
3512B Marine Auxiliary Engine MID 111 - CID 1213 - FMI 04 Thermocouple #13 short to ground
3512B Marine Auxiliary Engine MID 111 - CID 1212 - FMI 05 Thermocouple #12 open circuit
3512B Marine Auxiliary Engine MID 111 - CID 1212 - FMI 04 Thermocouple #12 short to ground
3054 Truck Engine Crankshaft Pulley
3512B Marine Auxiliary Engine MID 036 - CID 0444 - FMI 03 Start Relay short to +batt
3126B Engines for Caterpillar Built Machines Water Temperature Regulator Housing - Remove and Install
3512B Marine Auxiliary Engine MID 047 - CID 0444 - FMI 03 Start Relay short to +batt
3512B Marine Auxiliary Engine MID 047 - CID 0446 - FMI 05 Air Shutoff Relay open
3500B Engines Turbocharger - Remove - Center Mounted Turbocharger
SR4B Generators Exciter - Remove and Install
3406E On-Highway Engine Engine Oil Cooler - Install
3500B Engines Turbocharger - Install - Center Mounted Turbocharger
3512B Marine Auxiliary Engine MID 111 - CID 1353 - FMI 03 Engine Air Mnfld Out Temp Sens open/short to +batt
3512B Marine Auxiliary Engine MID 111 - CID 1353 - FMI 04 Engine Air Mnfld Outlet Temp Sensor short to gnd
3512B Marine Auxiliary Engine MID 111 - CID 1354 - FMI 03 Right Turbo Air Out Temp Sens open/short to +batt