317B Excavator Machine System and Attachment Specifications Caterpillar


Cycle Times

Usage:

317B LN 6DZ

Boom, Stick, Bucket, Swing Movement And Travel

Engine setting at high idle ... 2300 ± 50 rpm

Oil temperature ... 55 ± 5°C (131 ± 9°F)

Check the specified relief valve pressure settings.

Cycle times are measured with the following attachments: 5.1 m (16 ft 8 inch) boom, 2.6 m (8 ft 6 inch) and SAE 0.65 m3 (0.85 yd3) empty bucket .

Place the power mode selector switch in the Power Mode position.

Place the work mode selector switch in the Boom Priority Mode position.

Boom Raise

Boom raise cycle time is the time period that elapses while the boom travels from the ground level to maximum boom height. The stick cylinder and the bucket cylinder must be fully retracted. Start with the bucket on the ground.

Boom raise cycle time ... 2.9 to 3.5 seconds

Boom Lower

Boom lower cycle time is the time period that elapses while the boom travels from maximum boom height to ground level. The stick cylinder and the bucket cylinder must be fully retracted.

Boom lower cycle time ... 1.9 to 2.5 seconds

Stick Out

Stick out cycle time is the time period for the full retraction of the stick cylinder. Start with the boom parallel to the ground and close the bucket.

Stick out cycle time ... 2.2 to 2.8 seconds

Stick In

Stick in cycle time is the time period for the full extension of the stick cylinder. Start with the boom parallel to the ground and close the bucket.

Stick in cycle time ... 2.3 to 2.9 seconds

Bucket Close

Bucket close cycle time is the time period for the full extension of the bucket cylinder.

Bucket close cycle time ... 3.4 to 4.0 seconds

Bucket Open

Bucket open cycle time is the time period for the full retraction of the stick cylinder.

Bucket open cycle time ... 1.7 to 2.3 seconds

Swing Movement

Swing cycle time is the time period for a 180 degree swing movement of the upper structure. Park the machine on a level, hard surface. Position the machine at maximum reach. Use an empty bucket. Begin the test with the upper structure in motion.

Swing cycle time ... 5.1 seconds maximum

Travel

Travel cycle time is the time period that elapses while the machine travels 20 m (65 ft 7 inch) after a preliminary 5 m (16 ft 5 inch) run.

Travel cycle time at HIGH speed ... 16.1 second maximum

Travel cycle time at LOW speed ... 26.1 seconds maximum

Caterpillar Information System:

302.5 Mini Hydraulic Excavator Hydraulic System Pressure - Release
302.5 Mini Hydraulic Excavator Hydraulic Oil Contamination - Test
320B Excavator Machine System Specifications Lines (Pilot) - Harvester
317B Excavator Machine System and Attachment Specifications Lines (Front) - VAB Double Action
3046 Engine For Caterpillar Built Machines Lifter Group - Remove and Install
3064 and 3066 Engines for Caterpillar Built Machines Water Temperature Regulator
M312, M315, M318 and M320 Excavators Hydraulic System Pump Control (Swing)
M312, M315, M318 and M320 Excavators Hydraulic System Gear Pump (Charge)
3046 Engine For Caterpillar Built Machines Cylinder Head - Install
320B Excavator Machine System Specifications Bucket
M312, M315, M318 and M320 Excavators Hydraulic System Pump Control (Main Hydraulic)
317B Excavator Machine System and Attachment Specifications Lines (Boom Cylinder) - Right Hand (with BLCV)
307B Excavator Supplement for 4M40 Engine Alternator - Remove and Install
330B Excavator Machine System Specifications Lines (Pump)
307B Excavator Supplement for 4M40 Engine Electric Starting Motor - Remove and Install
307B Excavator Supplement for 4M40 Engine Fuel Filter (Primary) and Fuel Filter Base - Remove and Install
307B Excavator Supplement for 4M40 Engine Water Separator - Remove and Install
307B Excavator Supplement for 4M40 Engine Engine Oil Level Gauge (Dipstick) - Remove and Install
216, 226, 228, 232, 236, 242, 246, 248, 252 and 262 Skid Steer Loaders Bucket Tips - Inspect/Replace
330B and 330B L Excavators Shipping Specifications
330B Excavator Machine System Specifications Lines (Front)
307B Excavator Supplement for 4M40 Engine Engine Oil Filter and Oil Filter Base - Remove and Install
307B Excavator Supplement for 4M40 Engine Air Cleaner - Remove and Install
330B Excavator Machine System Specifications Lines (Swing Motor)
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.