Front Idler, Recoil Spring and Hydraulic Track Adjuster - Remove and Install
Removal Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
A     | 138-7573     | Link Bracket     | 1     |
Start By:
- Separate the track assemblies. Refer to Disassembly and Assembly, "Track - Separate" in this manual.
- Remove one of the mounting bolts that hold the cover over the front of the recoil spring assembly. Fasten Tooling (A) to the front support for the recoil spring, as shown. Fasten Tooling (A) in the bolt hole for the cover.
Show/hide table
Illustration 1 | g00483037 |
- Fasten a hoist to front idler (1) and Tooling (A) , as shown.
- Slide front idler (1) , the recoil spring and hydraulic track adjuster (2) out of the undercarriage frame as a unit. The weight of the unit is approximately 204 kg (450 lb) .
Show/hide table
Illustration 2 | g00368999 |
- Remove four bolts (3) that hold the front idler to the front support for the recoil spring. Separate the front idler from the recoil spring and the hydraulic track adjuster. The weight of the front idler is approximately 109 kg (240 lb). The weight of the recoil spring and the hydraulic track adjuster as a unit is approximately 95 kg (210 lb) .
Installation Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
A     | 138-7573     | Link Bracket     | 1     |
- Be sure that the mating surfaces on the front support for the recoil spring are clean and free of dirt and debris prior to assembly. Be sure that the mating surfaces on the two bearings for the front idler are clean and free of dirt and debris prior to assembly.
- Fasten a hoist to the recoil spring and the hydraulic track adjuster. Put the unit in position on the front idler. Temporarily install four bolts (3) that hold the unit together.
Show/hide table
Illustration 3 | g00368999 |
- Install Tooling (A) on the front support for the recoil spring. Fasten a hoist to the front idler and Tooling (A) .
- Partially slide the front idler, the recoil spring and the hydraulic track adjuster into the undercarriage frame. Leave bolts (3) exposed. Remove the hoist from the unit. Remove Tooling (A) from the unit. Tighten bolts (3) .
Show/hide table
Illustration 4 | g00483037 |
- Install the mounting bolt that holds the cover to the front of the recoil spring assembly.
- Use a pry bar to slide the front idler into the undercarriage frame.
End By: Connect the track assemblies. Refer to Disassembly and Assembly, "Track - Connect" in this manual.
Caterpillar Information System:
315B Excavator Excavator Systems Track - Connect
320B Excavator Machine System Specifications Lines (Front)
320B Excavator Machine System Specifications Fuel Tank
5130 Excavator Hydraulic System Control Valve (Travel Parking Brake Dual Pressure)
302.5 Mini Hydraulic Excavator Fuel Tank Water and Sediment - Drain
302.5 Mini Hydraulic Excavator Blade Linkage - Lubricate
302.5 Mini Hydraulic Excavator Cooling System Coolant Level - Check
315B Excavator Excavator Systems Track Roller - Install
315B Excavator Excavator Systems Track Roller - Assemble
302.5 Mini Hydraulic Excavator Cooling System Hoses - Inspect
315B Excavator Excavator Systems Track Roller - Disassemble
3176C and 3196 Industrial Engines Electronic Control Module - Remove and Install
320B Excavator Machine System Specifications Lines (Front)
315B Excavator Excavator Systems Front Idler - Disassemble
3046 Engine For Caterpillar Built Machines Exhaust Manifold - Remove and Install
315B Excavator Excavator Systems Front Idler - Assemble
3406E On-Highway Engine Engine Oil Pump - Assemble
3176C and 3196 Engines For Caterpillar Built Machines Connecting Rod Bearings - Remove
315B Excavator Excavator Systems Recoil Spring - Disassemble
315B Excavator Excavator Systems Recoil Spring - Assemble
318B Excavator Machine System Specifications Final Drive
302.5 Mini Hydraulic Excavator Hydraulic System Oil Cooler Core - Clean
3176C and 3196 Engines For Caterpillar Built Machines Connecting Rod Bearings - Install
320B Excavator Machine System Specifications Governor Control