Crankcase Explosion Relief Valve - Remove and Install
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
Show/hide table
注意 |
---|
在检查、保养、测试、调整及维修产品时,请小心确保盛接油液。 在打开任何舱室或拆卸任何含有油液的部件前,请准备好盛接液体用的适当容器。 |
- 拆下六条螺栓 (1)。
- 卸下曲轴箱防爆安全阀 (2)。 更换 O 形密封圈。
Show/hide table
图 1 | g00605092 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
Show/hide table
注意 |
---|
在检查、保养、测试、调整及维修产品时,请小心确保盛接油液。 在打开任何舱室或拆卸任何含有油液的部件前,请准备好盛接液体用的适当容器。 |
- 将甘油涂敷在曲轴箱防爆安全阀 (2) 的 O 形密封圈上。
- 将 5P-3413 管道密封剂涂敷在螺栓 (1) 上。
- 将曲轴箱防爆安全阀安装至曲轴箱盖上。
注: 安装阀门时,将曲轴箱防爆安全阀放置在合适位置,使排气口正面朝下。
Show/hide table
图 2 | g00605092 |
Caterpillar Information System:
G3612 and G3616 Engines Crankcase Pressure Sensor - Remove and Install
G3612 and G3616 Engines Exhaust Bypass - Install
3176B Marine Engine Starting the Engine
3114, 3116 and 3126 Engines Excessive Black Smoke
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Inlet Manifold - Install - 3013, 3014, and 3024 Engines
3114, 3116 and 3126 Engines Engine Will Not Crank
3606 and 3608 Engines General Information (Cooling System)
3114, 3116 and 3126 Engines Engine Vibration
3500B Engines Engine Oil Filter Base - Install - Spin-on Filters
3606 and 3608 Engines Pressure Regulating Valve
3500B Engines Engine Oil Filter Base - Assemble - Spin-on Filters
3306B Generator Set Electronic Modular Control Panel II (EMCP II)
3512B Marine Auxiliary Engines Valve Cover - Remove and Install
G3612 and G3616 Engines Coolant Mixer Housing - Remove and Install
3512B Marine Auxiliary Engines Rocker Shaft and Push Rods - Remove
3606 and 3608 Engines Connecting Rod Bearings
G3612 and G3616 Engines Water Pump - Remove
3512B Marine Auxiliary Engines Rocker Shaft and Push Rods - Install
G3612 and G3616 Engines Water Pump - Install
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Electric Starting Motor
3612 and 3616 Engines Water Pump - Disassemble
3408E and 3412E Engines for Caterpillar Built Machines Cylinder Liner - Install
3612 and 3616 Engines Water Pump - Assemble
3612 and 3616 Engines Water Pump Seal - Remove