Engine Oil Filter Base - Install - Spin-on Filters
Show/hide table
| 需要的工具 | |||
| 工具 | 零件号 | 零件描述 | 数量 |
| B | 138-7575 | 连杆支架 | 2 |
Show/hide table
| 注意 |
|---|
|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将工具 (B)和适当起吊设备连接到机油滤清器底座上。 机油滤清器座的重量约为
39 kg (86 lb) 。 提升机油滤清器座使之就位。 安装螺栓 (1)以将机油滤清器座和发动机固定在一起。 - 安装弯头 (3)和接头 (2)密封垫。 用螺栓安装弯管 (2)和接头 (3)。
- 确保机油滤清器安装面清洁。 在机油滤清器的密封上涂抹清洁的发动机机油。 根据滤清器上的说明安装滤清器 (4)。 禁止过度拧紧滤清器。
- 使线束夹就位。 在夹子上安装螺栓。
- 用机油注入发动机。 参考操作和保养手册, "加注容量"。
Show/hide table
| |
| 图 1 | g00604291 |
Caterpillar Information System:
3606 and 3608 Engines Pressure Regulating Valve
3500B Engines Engine Oil Filter Base - Assemble - Spin-on Filters
3306B Generator Set Electronic Modular Control Panel II (EMCP II)
3500B Engines Engine Oil Filter Base - Disassemble - Spin-on Filters
3500B Engines Engine Oil Filter Base - Remove - Spin-on Filters
3500B Engines Engine Oil Filter Housing - Install
3114, 3116 and 3126 Engines Engine Stalls at Low RPM
3114, 3116 and 3126 Engines Engine Oil in Exhaust System
3500B Engines Engine Oil Filter Housing - Remove
CIPI UNDERCARRIAGE Arrangements: 1667049, 2372904, 3Q6481, 6Z7988, 6Z7989, 9Q5032, 9Q5040, 9Q5043, 9Q5046, 9Q5047, 9Q5066, 9Q5074, 9Q5097, 9Q5098, 9Q5116, 9Q5134, 9Q5136, 9Q5142, 9Q5147, 9Q5148, 9Q5149, 9Q5172 and 9Q5204 Travel Hydraulic System
3114, 3116 and 3126 Engines Engine Oil in Cooling System
3500B Engines Engine Oil Pump - Install
3114, 3116 and 3126 Engines Engine Vibration
3606 and 3608 Engines General Information (Cooling System)
3114, 3116 and 3126 Engines Engine Will Not Crank
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Inlet Manifold - Install - 3013, 3014, and 3024 Engines
3114, 3116 and 3126 Engines Excessive Black Smoke
3176B Marine Engine Starting the Engine
G3612 and G3616 Engines Exhaust Bypass - Install
G3612 and G3616 Engines Crankcase Pressure Sensor - Remove and Install
G3612 and G3616 Engines Crankcase Explosion Relief Valve - Remove and Install
3512B Marine Auxiliary Engines Valve Cover - Remove and Install
G3612 and G3616 Engines Coolant Mixer Housing - Remove and Install
3512B Marine Auxiliary Engines Rocker Shaft and Push Rods - Remove