Gas Pressure Regulator - Assemble
组装步骤
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 组装大型膜片组件。
Show/hide table
图 1 | g00595761 |
(23) 盖。 (54) 导向装置。 (55) 垫圈。 (56) 膜片。 (57) 接头。 (58) 护圈。 (59) 轴。 |
- 安装膜片 (56) 。
Show/hide table
图 2 | g00595758 |
Show/hide table
图 3 | g00595759 |
- 安装垫圈 (55) 。
- 将导向装置 (54) 安装在盖 (23) 上。
- 将轴组件 (53) 安装至盖 (23) 内。
- 组装阀柱塞组件。
Show/hide table
图 4 | g00595757 |
(40) 销。 (48) 轴。 (49) 阀室盖。 (50) 衬套。 (51) 护圈。 (52) 螺钉。 |
- 组装气压调节器的盖。
Show/hide table
图 5 | g00595755 |
(40) 销。 (41) 轴组件。 (42) 销。 (43) 固定夹。 (44) 臂。 (45) 密封件。 (46) 螺母。 (47) 盖。 |
- 将臂 (44) 和轴 (41) 定位在调节器壳体内。 安装两个新的固定夹 (43) 和销 (42) 。
Show/hide table
图 6 | g00595754 |
- 将开口销 (40) 安装在轴组件 (41) 内。
Show/hide table
图 7 | g00595752 |
- 如果卸下阀柱塞组件,则将阀柱塞组件 (39) 安装在 T 形管内。
Show/hide table
图 8 | g00595751 |
- 安装大尺寸 T 形管 (38) 。
- 组装小型膜片组件 (31) 。
Show/hide table
图 9 | g00595749 |
(33) 阀。 (34) 膜片。 (35) O 形密封圈。 (36) 垫圈。 (37) 适配器。 |
- 卸下喷嘴 (32) 。
Show/hide table
图 10 | g00595747 |
Show/hide table
图 11 | g00595748 |
- 将外壳上部 (30) 安装在膜片组件 (31) 内。
- 安装垫圈 (28) 和膜片组件 (29) 。 确保将膜片安置在恰当位置。
- 安装垫圈 (27) 。
Show/hide table
图 12 | g00595746 |
- 安装上部黄铜接头 (26) 。
- 翻转壳体。
- 安装下部黄铜接头 (25) 。
Show/hide table
图 13 | g00595744 |
- 将盖 (23) 、轴和膜片作为整体进行安装。
Show/hide table
图 14 | g00595743 |
- 将十二个螺栓 (24) 安装在壳体 (23) 内。
Show/hide table
图 15 | g00595605 |
- 安装护圈 (21) 和弹簧 (22) 。
注: 确保将螺纹护圈拧至恰当位置。
注: 小心地将弹簧安装至壳体内。 弹簧受压。
Show/hide table
图 16 | g00595603 |
- 请检查垫片是否损坏。 如有必要,更换垫片。 安装壳体 (19) 和垫片。
Show/hide table
图 17 | g00595600 |
- 安装四个螺栓 (20) 。
- 翻转气压调节器。
- 安装接头 (18) 。
Show/hide table
图 18 | g00595596 |
- 安装垫圈 (16) 和弹簧 (17) 。
Show/hide table
图 19 | g00595593 |
- 安装壳体 (14) 。
Show/hide table
图 20 | g00595590 |
- 安装八个螺栓 (15) 。
- 组装滤芯组件 (8) 。
Show/hide table
图 21 | g00595587 |
(7) 阀体。 (9) 螺钉。 (10) 垫圈。 (11) 滤芯。 (12) 垫圈。 (13) 盖。 |
- 将阀体 (7) 安装至滤芯组件 (8) 内。
Show/hide table
图 22 | g00595584 |
- 安装阀 (6) 。
Show/hide table
图 23 | g00595582 |
- 安装管组件 (4) 。
Show/hide table
图 24 | g00595580 |
- 安装管组件 (5) 。
- 拧紧调整螺钉。
注: 确保调整螺钉回到原始位置。
Show/hide table
图 25 | g00595577 |
- 拧紧防松螺母 (2) 。
Show/hide table
图 26 | g00592537 |
End By: 安装气压调节器 (1) 。
Caterpillar Information System:
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 110 FMI 2 Temperature Sensor (Engine Coolant) Incorrect Signal - Test
C-10 and C-12 Truck Engines Solenoid Valve (Compression Brake) - Test
CIPI UNDERCARRIAGE Arrangements: 9Q5221, 9Q5234, 9Q5243, 9Q5245, 9Q5246, 9Q5247, 9Q5385, 9Q5433, 9Q5482, 9Q5622, 9Q5661, 9Q5719, 9Q5720, 9Q5721, 9Q5722, 9Q5830, 9Q5840, 9Q5857, 9Q5874, 9Q5883, 9Q5930 and 9Q5940 Commercial Oils
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 100 FMI 4 Pressure Sensor (Engine Oil) Voltage Below Normal - Test
C-10 and C-12 Truck Engines Control Valve (Compression Brake) - Test
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 100 FMI 3 Pressure Sensor (Engine Oil) Voltage Above Normal - Test
C-10 and C-12 Truck Engines Slave Piston Lash - Adjust
3176C and 3196 Engines for Caterpillar Built Machines Vibration Damper - Check
3408E and 3412E Engines for Caterpillar Built Machines Flywheel Housing - Inspect
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 100 FMI 2 Pressure Sensor (Engine Oil) Incorrect Signal - Test
3306C Engines for Caterpillar Built Machines Flywheel - Inspect
3126B Marine Engine Auxiliary Water Pump
3406E and 3456 Generator Set Engines Gear Group (Front) - Remove
G3606 and G3608 Engines Air Inlet Choke - Install
3408E and 3412E Engines for Caterpillar Built Machines Battery - Test
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 110 FMI 3 Temperature Sensor (Engine Coolant) Voltage Above Normal - Test
3408E and 3412E Engines for Caterpillar Built Machines Charging System - Test
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Water Temperature Regulator - Remove and Install
3408E and 3412E Engines for Caterpillar Built Machines Excessive Bearing Wear - Inspect
C-10 and C-12 Industrial Engines Excessive Engine Oil Consumption - Inspect
3408E and 3412E Engines for Caterpillar Built Machines Increased Engine Oil Temperature - Inspect
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 110 FMI 4 Temperature Sensor (Engine Coolant) Voltage Below Normal - Test
3126B Marine Engine Cylinder Block Cover Group
3406E and 3456 Generator Set Engines Gear Group (Front) - Install