Track Roller - Install
Installation Procedure for the Track Roller on CIPI Undercarriage Arrangements which are Based on 330, 330B, and 330C Track Type Excavators
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
A     | 8S-7611     | Tube Assembly     | 2     |
8S-7615 | Pin     | 2     | |
8S-7640 | Stand Group     | 2     | |
B (1)     | FT-1310     | Track Roller Lifting Fork     | 1     |
C (2)     | 183-4797     | Track Roller Lifting Fork     | 1     |
Show/hide table
( 1 ) | Use FT-1310 Track Roller Lifting Fork to remove the track rollers from CIPI undercarriage arrangements which are based on 330 and 330B track type excavators. |
( 2 ) | Use 183-4797 Track Roller Lifting Fork to remove the track rollers from CIPI undercarriage arrangements which are based on 330C track type excavators. |
Note: There is a track guide on each side of the machine. The procedure which follows is for the installation of the track roller with the track guide.
- Make sure that the mounting surfaces on the track roller, the track guide, the rock guards (if equipped), and the undercarriage frame assembly are clean and free of dirt and debris prior to installing.
- Fasten a suitable lifting device to Tooling (B) or Tooling (C). Use Tool (B) or Tool (C) to put track roller (2) in position on the undercarriage frame assembly. The weight of the track roller is approximately 54 kg (120 lb). Make sure that the filler plug in the track roller is facing toward the outside of the undercarriage frame assembly. Install the four bolts that hold the track roller in position.
Show/hide table
Illustration 1 | g00489838 |
- Use Tooling (B) or Tooling (C) to put track guide (1) in position on the undercarriage frame assembly. Install the four bolts that secure the guide.
Show/hide table
Illustration 2 | g00489833 |
- Install the rock guards, if equipped.
Show/hide table
Illustration 3 | g00489835 |
- Prior to lowering the machine to the ground and tightening the track, make sure that all of the track rollers rotate smoothly by manually turning the track rollers.
- Lift the machine off Tooling (A). Remove Tooling (A) from the machine. Lower the machine to the floor.
Show/hide table
Illustration 4 | g00489826 |
- Tighten the tension of the track. Refer to Operation and Maintenance Manual, "Track Adjustment - Adjust" for the correct procedure.
Caterpillar Information System:
CIPI UNDERCARRIAGE Arrangements: 9Q5221, 9Q5234, 9Q5243, 9Q5245, 9Q5246, 9Q5247, 9Q5385, 9Q5433, 9Q5482, 9Q5622, 9Q5661, 9Q5719, 9Q5720, 9Q5721, 9Q5722, 9Q5830, 9Q5840, 9Q5857, 9Q5874, 9Q5883, 9Q5930 and 9Q5940 Track Roller - Remove
3126B Marine Engine Diagnostic Flash Code Retrieval
3126B Marine Engine Sensors and Electrical Components
3114, 3116 and 3126 MUI Engine Governors Governor (Type III) - Disassemble
3500B and 3500 Marine Propulsion Engines with EUI Option Cooling System Coolant (ELC) - Change
CIPI UNDERCARRIAGE Arrangements: 1667049, 2372904, 3Q6481, 6Z7988, 6Z7989, 9Q5032, 9Q5040, 9Q5043, 9Q5046, 9Q5047, 9Q5066, 9Q5074, 9Q5097, 9Q5098, 9Q5116, 9Q5134, 9Q5136, 9Q5142, 9Q5147, 9Q5148, 9Q5149, 9Q5172 and 9Q5204 Track Carrier Roller - Assemble
3126B Marine Engine Engine Rating Definitions
3126B Marine Engine Zinc Rods - Inspect/Replace
3126B Marine Engine Engine Oil Level Gauge - Calibrate
3126B Marine Engine Refill Capacities
CIPI UNDERCARRIAGE Arrangements: 9Q5221, 9Q5234, 9Q5243, 9Q5245, 9Q5246, 9Q5247, 9Q5385, 9Q5433, 9Q5482, 9Q5622, 9Q5661, 9Q5719, 9Q5720, 9Q5721, 9Q5722, 9Q5830, 9Q5840, 9Q5857, 9Q5874, 9Q5883, 9Q5930 and 9Q5940 Track Carrier Roller - Disassemble
CIPI UNDERCARRIAGE Arrangements: 1667049, 2372904, 3Q6481, 6Z7988, 6Z7989, 9Q5032, 9Q5040, 9Q5043, 9Q5046, 9Q5047, 9Q5066, 9Q5074, 9Q5097, 9Q5098, 9Q5116, 9Q5134, 9Q5136, 9Q5142, 9Q5147, 9Q5148, 9Q5149, 9Q5172 and 9Q5204 Track Carrier Roller - Install
3612 and 3616 Engines Camshaft - Earlier
CIPI UNDERCARRIAGE Arrangements: 1667049, 2372904, 3Q6481, 6Z7988, 6Z7989, 9Q5032, 9Q5040, 9Q5043, 9Q5046, 9Q5047, 9Q5066, 9Q5074, 9Q5097, 9Q5098, 9Q5116, 9Q5134, 9Q5136, 9Q5142, 9Q5147, 9Q5148, 9Q5149, 9Q5172 and 9Q5204 Track Roller - Disassemble
CIPI UNDERCARRIAGE Arrangements: 1667049, 2372904, 3Q6481, 6Z7988, 6Z7989, 9Q5032, 9Q5040, 9Q5043, 9Q5046, 9Q5047, 9Q5066, 9Q5074, 9Q5097, 9Q5098, 9Q5116, 9Q5134, 9Q5136, 9Q5142, 9Q5147, 9Q5148, 9Q5149, 9Q5172 and 9Q5204 Track Roller - Assemble
3406E and 3456 Generator Set Engines Speed/Timing Sensor - Remove and Install
3126B Marine Engine Model View Illustrations
3114, 3116 and 3126 MUI Engine Governors Governor (Type III) - Assemble
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Cylinder Head - Remove
3408E and 3412E Engines for Caterpillar Built Machines Engine Support (Front) - Remove and Install
3612 and 3616 Engines Camshaft - Later
3114, 3116 and 3126 MUI Engine Governors Governor (Type IV) - Disassemble
3406E and 3456 Generator Set Engines Electronic Control Module - Remove and Install
3176B Marine Engine Model View Illustrations