Prelubrication Oil Pump - Assemble
组装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
A     | 1P-0510     | 起子总成     | 1     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 使用工具 (A) 将唇形密封件 (7) 安装到壳体 (4) 中。 在密封唇朝向内部时,安装内部唇形密封件。 在密封唇朝向外部时,安装外部唇形密封件。 将清洁的发动机机油涂抹在唇形密封件的密封唇上。
注: 更多信息,请参阅拆解和装配一般信息, "(参考资料)"。
Show/hide table
图 1 | g01307950 |
- 在转子 (6) 上涂抹干净的发动机机油。 将转子 (6) 安装在壳体 (4) 中。
Show/hide table
图 2 | g01307954 |
- 在惰轮 (5) 上涂抹干净的发动机机油。 将惰轮 (5) 安装到转子 (6) 中。
Show/hide table
图 3 | g01307956 |
- 安装原有的垫片 (8) 。
Show/hide table
图 4 | g01307965 |
- 将惰轮 (5) 放置到位,以便盖 (3) 内的轴和惰轮结合。 对齐头部件和壳体 (4) 上的标记。 安装头部件 (3) 。
- 检查预润滑机油泵的端间隙。 测量转子后部和壳体底座加工面之间的间隙。 通过孔开口插入塞尺。 该端隙必须为 0.013 至 0.076 mm (0.0005 至 .0.0030 in)。
- 如有必要,卸下缸盖。 增加或去掉垫片 (8) ,以获得正确的端隙。
Show/hide table
图 5 | g01307973 |
- 将空气驱动马达 (1) 或电动马达上的标记和预润滑机油泵 (2) 上的标记对齐。 将马达轴上的钥匙和预润滑机油泵内的锁孔接合。
Show/hide table
图 6 | g00546236 |
- 使两个装置结合到一起。 安装将两个装置固定在一起的螺栓。
End By: 安装预润滑机油泵。 请参阅 拆解和组装, "预润滑机油泵 - 安装"。
Caterpillar Information System:
3600 and C280 Diesel Engine Fluids Recommendations Crude Fuel Oil
3054 and 3056 Industrial and Generator Set Engines Water Pump - Assemble
Electronic Modular Control Panel II+ (EMCP II+) Block Diagram of Generator Set Control
EMCPII+ for Gas Engines Connector Contact Identification of Generator Set Control
3406C (PEEC III) Truck Engines Fuel System
3612 and 3616 Fast Vessel Engines Maintenance Records
3412E and C30 Marine Engines Fuel System
797 Off-Highway Truck Braking System Hydraulic Tank Mounting
3412E and C30 Marine Engines Lubrication System
3054 Engine for Caterpillar Built Machines Camshaft Bearings - Remove and Install
G3606 and G3608 Engines Prelubrication Oil Pump - Disassemble
3408E and 3412E Engines for Caterpillar Built Machines Unit Injector Hydraulic Pump Drive - Install
3408E and 3412E Engines for Caterpillar Built Machines Speed/Timing Sensor - Remove and Install
3612 and 3616 Fast Vessel Engines Cooling System Coolant (ELC) - Change
Electronic Modular Control Panel II+ (EMCP II+) Pulse Width Modulated (PWM) Sensor - Test
3054 and 3056 Industrial and Generator Set Engines Water Temperature Regulator - Remove and Install
3054 Engine for Caterpillar Built Machines Camshaft - Remove and Install
3054 Engine for Caterpillar Built Machines Flywheel - Remove
Guidelines For 3600 Heavy Fuel Oil (HFO) Engines{1000} Guidelines For 3600 Heavy Fuel Oil (HFO) Engines{1000}
3054 Engine for Caterpillar Built Machines Flywheel - Install
3054 and 3056 Industrial and Generator Set Engines Front Cover - Remove and Install
G3606 and G3608 Engines Lubrication Metering Pump - Remove and Install
3054 Engine for Caterpillar Built Machines Front Cover - Install
G3606 and G3608 Engines Engine Oil Pump - Remove