Crankshaft Front Seal - Remove
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件名称     | 数量     |
A     | 1P-0510     | 冲头总成     | 1     |
B     | 5P-7315     | 承磨衬套破坏环     | 1     |
C     | 5P-7312     | 油封破坏工具     | 1     |
开始:
- 拆卸减振器和皮带轮。 请参考解体与组装, "减振器和皮带轮 - 拆卸和安装"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
机器做检查、保养、测试、调整和修理时,必须小心,不让油液流出。 在打开任何舱室或解体任何储有液体的零件之前,要准备好合适的容器收集流出液体。 有关可提供予卡特彼勒机器的工具及适合于盛装油液的容器,请参阅专门出版物, NENG2500, "卡特彼勒工具及车间用品指南"。 按照本地法规和指令处置所有液体。 |
注: 更换曲轴油封时,也必须更换承磨衬套。
- 拆下两根螺栓、垫圈、隔套和将曲轴油封接头 (2) 固定到位的卡箍 (1) 。 从发动机上拆下曲轴油封接头 (2) 和 O 形密封圈。
Show/hide table
图 1 | g00504503 |
- 使用工具 (A) 和压力机将曲轴油封从曲轴油封接头 (2) 上拆下。
- 将 O 形密封圈和曲轴油封接头 (2) 安装到发动机上。 安装两根螺栓、垫圈、隔套和卡箍 (1) ,以便将曲轴油封接头 (2) 固定到位。
- 将工具 (B) 安装在油封接头 (2) 的孔中,如图所示。
Show/hide table
图 2 | g00510634 |
- 将工具 (C) 安装在工具 (B) 与承磨衬套之间。 使用扳手转动工具 (C) ,直到工具边缘使得承磨衬套产生了平的折痕。 重复此步骤,直到承磨衬套中出现足够多的平折痕,以便使承磨衬套能够从曲轴端滑脱。
Show/hide table
注意 |
---|
应小心确保密封件破坏工具不会切穿承磨衬套。 曲轴表面的损坏可能导致可能的油封泄漏。 |
- 拆卸工具 (B) 和 (C) 。 用手拆下承磨衬套。
Caterpillar Information System:
3306B Industrial Engine Magnetic Pickup
3306B Industrial Engine Shutoff Solenoid
3406C Engines for Caterpillar Built Machines Cylinder Block
3114, 3116 and 3126 MUI Engine Governors Governor Performance Data
3114, 3116 and 3126 MUI Engine Governors Specification
3114, 3116 and 3126 MUI Engine Governors Governor (Type VI)
3114, 3116 and 3126 MUI Engine Governors Governor (Type V)
3114, 3116 and 3126 MUI Engine Governors Governor (Type IV)
3306B Industrial Engine Air Starting Motor
3114, 3116 and 3126 MUI Engine Governors Governor (Type III)
3114, 3116 and 3126 MUI Engine Governors Governor (Type II)
G3304 and G3306 Engines Electric Starting Motor
3304B and 3306B Engines for Caterpillar Built Machines Crankshaft Main Bearings - Remove
3408E and 3412E Engines for Caterpillar Built Machines Cylinder Liner - Remove
3304B and 3306B Engines for Caterpillar Built Machines Crankshaft Main Bearings - Install
3406C (PEEC III) Truck Engine Connecting Rod
Gas Engine Driven Chiller Driveline Pneumatic Drum Clutch - Lubricate
3408E and 3412E Engines for Caterpillar Built Machines Valve Rocker Arms, Lifters, and Bridges
3304B and 3306B Engines for Caterpillar Built Machines Cylinder Head - Remove
3406E Truck Engines BrakeSaver
Gas Engine Driven Chiller Driveline Pneumatic Drum Clutch Air Control Components - Inspect
3306B Industrial Engine Start Switch
Gas Engine Driven Chiller Driveline Walk-Around Inspection
P16, P20, P25, P28, P40 and P60 Pulverizers Cutter