Flywheel Housing - Remove and Install
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件名称     | 数量     |
A     | 138-7573     | 连接支架     | 2     |
开始:
- 拆卸飞轮。 请参考解体与组装, "飞轮 - 拆卸"。
- 拆卸曲轴后油封。 请参考解体及组装, "曲轴后密封 - 拆卸"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 拆下将油底壳护板固定到飞轮壳上的螺栓。 松开将油底壳护板固定到位的其余螺栓。 将隔套放置在缸体和油底壳护板之间。 必须进行此项操作,以免油底壳护板密封垫损坏。
注: 如果油底壳护板密封垫损坏,必须拆下油底壳护板。 请参考解体与组装, "发动机油底壳护板 - 拆卸和安装"。
- 拆下涡轮增压器机油回油管 (1) 。
Show/hide table
图 1 | g00516402 |
- 将工具 (A) 安装在飞轮壳上。 将起重机固定到飞轮壳上的工具 (A) 上。
- 从发动机上拆下全部螺栓 (2) 和飞轮壳。 飞轮壳的重量为37 kg (82 lb)。
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件名称     | 数量     |
A     | 138-7573     | 连接支架     | 2     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将密封垫放置到位,然后使用起重机将飞轮壳在发动机上放置到位。
- 安装将飞轮固定到发动机上的全部螺栓 (2) 。 将螺栓拧紧至扭矩 100 ± 14 N·m (74 ± 10 lb ft)。
Show/hide table
图 2 | g00516402 |
- 从发动机上拆下工具 (A) 和起重机。
- 安装涡轮增压器机油回油管 (1) 。
- 修整飞轮壳体密封垫,使密封垫与缸体底部轮廓一致。
注: 如果油底壳护板已拆下,安装一个新的密封垫和油底壳护板。 请参考解体与组装, "发动机油底壳护板 - 拆卸和安装"。
- 将 3S-6252 密封剂 涂覆在油底壳护板密封垫与飞轮壳密封垫之间的接触点上。
- 拆下安装在缸体与油底壳护板之间的隔套。 安装将油底壳护板固定到飞轮壳上的螺栓。 拧紧将油底壳护板固定到缸体上的其余螺栓。
End By:
- 拆卸曲轴后油封。 请参考 解体及组装, "曲轴后油封 - 安装"。
- 安装飞轮。 请参考 解体与组装, "飞轮 - 安装"。
Caterpillar Information System:
3306B Industrial Engine Camshaft Bearings - Remove and Install
3306B Industrial Engine Engine Oil Pan
3406E On-Highway Engine Valve Mechanism Cover - Remove and Install
3306B Industrial Engine Overhaul Considerations
3306C Engines for Caterpillar Built Machines Fuel Filter Base
P16, P20, P25, P28, P40 and P60 Pulverizers Rotator Motor
C-12 Truck Engine Cooling System
3304B and 3306B Engines for Caterpillar Built Machines Fuel Priming Pump - Remove and Install
3306B Industrial Engine Engine Oil Pressure
3304B and 3306B Engines for Caterpillar Built Machines Engine Oil Filter Base - Assemble
Gas Engine Driven Chiller Driveline Pneumatic Drum Clutch - Inspect
Gas Engine Driven Chiller Driveline Heat Exchanger - Clean
3406C (PEEC III) Truck Engine Compression Brake
3306B Industrial Engine Engine Support (Front)
3304B and 3306B Engines for Caterpillar Built Machines Engine Oil Pump - Remove
3306B Industrial Engine Engine Oil Level - Check
3306B Industrial Engine Engine Support (Front)
3406E On-Highway Engine Valve Mechanism Cover Base - Remove and Install
3306B Industrial Engine Engine Oil Pump - Install
3306B Industrial Engine Engine Oil Pump - Disassemble
Electronic Modular Control Panel II+ (EMCP II+) Paralleling Mode
3406C (PEEC III) Truck Engine Belt Tightener
3176C Engine Engine Design
3408E and 3412E Engines for Caterpillar Built Machines Alternator and Regulator