Protective Hose Sleeves Are Available for -12 Drive Motor Hoses on Certain Multi-Terrain and Compact Track Loaders {3154} Caterpillar

Protective Hose Sleeves Are Available for -12 Drive Motor Hoses on Certain Multi-Terrain and Compact Track Loaders {3154}

Usage:

289D A9Z

Compact Track Loader: 259B3 (S/N: YYZ1-UP); 259D (S/N: FTK1-UP; GTK1-UP; FTL1-UP); 279C (S/N: MBT1-UP); 279C2 (S/N: KWB1-UP); 279D (S/N: WEF1-UP; GTL1-UP; PPT1-UP; RCX1-UP); 289C (S/N: JMP1-UP); 289C2 (S/N: RTD1-UP); 289D (S/N: WCT1-UP; TAW1-UP; A9Z1-UP); 299C (S/N: JSP1-UP); 299D (S/N: GTC1-UP; HCL1-UP); 299D XHP (S/N: NLC1-UP; JST1-UP); 299D2 (S/N: FD21-UP; BY41-UP); 299D2 XHP (S/N: DX21-UP; DX91-UP)
Multi Terrain Loader: 287C (S/N: MAS1-UP); 247B3 (S/N: KB31-UP; ESL1-UP; TSL1-UP); 257B Series 3 (S/N: B7H1-UP); 257D (S/N: EML1-UP; FMR1-UP; EZW1-UP); 277C (S/N: JWF1-UP); 277C2 (S/N: MET1-UP); 277D (S/N: NTL1-UP; FMT1-UP; MLT1-UP); 287C2 (S/N: SSB1-UP); 287D (S/N: STK1-UP; TLK1-UP; HMT1-UP); 297C (S/N: GCP1-UP); 297D (S/N: BE71-UP); 297D XHP (S/N: HP71-UP); 297D2 (S/N: BL71-UP); 297D2 XHP (S/N: HP21-UP)

Hose sleeves are available for -12 drive motor hoses on the machines listed above. The sleeves provide added protection to the hoses and helps prevent failures from rubbing and chafing.

Installation

Show/hide table

Table 1
Required Parts
Item	Part Number	Part Name
1	339-6185	Tape⁽¹⁾
2	7K-1181	Cable Strap⁽²⁾
3	420-9999	Sleeve⁽³⁾

Show/hide table

⁽¹⁾	The tape roll is 25 m (27 yd) long and is enough to install approximately 200 sleeves.
⁽²⁾	Two cable straps are required for each sleeve.
⁽³⁾	The sleeve is 89 mm (3.5 in) long.

Show/hide table




Illustration 1	g03896598
(1) 339-6185 Tape

Show/hide table




Illustration 2	g03896600
(1) 339-6185 Tape (2) 7K-1181 Cable Strap (3) 420-9999 Sleeve

Locate sleeve (3) onto the drive hose in locations where the hose might be susceptible to rubbing machine components.
Note: If an existing hose has a fabric sleeve covering, cut and remove the fabric from the area where a sleeve is to be installed.
Wrap approximately 125 mm (5 in) or one and half wraps of tape (1) under each end of the sleeve. The tape provides friction under the sleeve to prevent the sleeve from sliding out of the desired location.
Secure the sleeve in place by installing a cable strap (2) at each end of the sleeve.