Muffler and Mounting - Remove and Install
Removal and Installation Procedure
- Remove bolt (2) and remove strap (1).
- Dimension (A) should measure
72.7± 6 mm (2.86 ± 0.2 inch) . Adjust muffler if necessary. Final adjustments may need made after the muffler is installed. - Replace strap (1) and tighten bolts (2) and (5) to a torque of
5 N·m (44 lb in) . Ensure that the strap is perpendicular to the muffler. - Remove bolt (3) and remove strap (4).
- Replace strap (4) and tighten bolts (3) and (6) to a torque of
5 N·m (44 lb in) . Ensure that the strap is perpendicular to the muffler. - Check straps (1) and (4) again ensuring the straps are perpendicular to the muffler.
- Tighten bolts (2), (3), (5), and (6) in order, to a torque of
20 ± 3 N·m (177 ± 27 lb in) .
Show/hide table
| |
| Illustration 1 | g06055076 |
Show/hide table
| |
| Illustration 2 | g06055120 |
Note: Replace straps (1) and (4) as a pair.
Note: The replacement of straps (1) and (4) can be performed without disconnecting or removing the muffler.
Caterpillar Information System:
SE50 VT Asphalt Screed Tamper Bar - Check and Adjust
CB64B, CB66B and CB68B Vibratory Asphalt Compactors Fuel System Primary Filter (Water Separator) - Replace
G3516 TA Engine ECM - Replace
422F2, 426F2, 428F2, 432F2, 434F2 and 444F2 Backhoe Loaders Maintenance Interval Schedule
C3.4B Engines for Caterpillar Built Machines Aftertreatment SCR System Dosing - Test
C3.4B Engines for Caterpillar Built Machines Diesel Exhaust Fluid Tank - Flush
2015/03/10 An Improved Sideshift Lock Lines are Now Used on Certain 424B Backhoe Loaders {5057, 5484}
Installation of Mechanically Attached Sidebar Protectors on Loader Bucket{6101, 6102, 6817} Installation of Mechanically Attached Sidebar Protectors on Loader Bucket{6101, 6102, 6817}
906K, 906M, 907K, 907M, 908K and 908M Compact Wheel Loaders Hoses and Clamps - Replace
CB64B, CB66B and CB68B Vibratory Asphalt Compactors Fuses - Replace
Installing Product Link Kits to F2 Series Backhoe Loaders{1408, 7490, 7601, 7603, 7610, 7620} Installing Product Link Kits to F2 Series Backhoe Loaders{1408, 7490, 7601, 7603, 7610, 7620}
C3.4B Engines for Caterpillar Built Machines Position the Valve Mechanism Before Maintenance Procedures
SE50 VT Asphalt Screed Temperature Sensor (Electric Heat) - Test
2015/02/27 The Assembly Procedure For The Blade Lift Cylinder Has Been Improved On Certain Motor Graders {5102}
416F2, 420F2 and 430F2 Backhoe Loaders Maintenance Interval Schedule
816K Landfill Compactor Hydraulic System Oil Sample - Obtain
CB64B, CB66B and CB68B Vibratory Asphalt Compactors Fuel System Secondary Filter - Replace
CB64B, CB66B and CB68B Vibratory Asphalt Compactors Fuel System Water Separator - Drain
CB64B, CB66B and CB68B Vibratory Asphalt Compactors Towing the Machine
CB64B, CB66B and CB68B Vibratory Asphalt Compactors Parking Brake Manual Release
2015/04/22 An Improved Plate Assembly Is Now Available for F Series Backhoe Loaders {5063}
Transmission Clutch Friction Discs May Experience Premature Wear on Certain 14M and 16M Motor Graders {3155} Transmission Clutch Friction Discs May Experience Premature Wear on Certain 14M and 16M Motor Graders {3155}
Communication Installation Gp (PL641 CELLULAR) Antennas May Be Missing Adhesive Strip on Bottom on All Cat® Products Equipped with Product Link{733B, 7606} Communication Installation Gp (PL641 CELLULAR) Antennas May Be Missing Adhesive Strip on Bottom on All Cat® Products Equipped with Product Link{733B, 7606}
2015/03/02 New Phone Number for VIMS Support Is Now Available for All Cat® Products Equipped with VIMS {7601}