Position the Valve Mechanism Before Maintenance Procedures
Show/hide table
NOTICE |
---|
Ensure that this procedure is carried out before the rocker shaft is removed. |
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A(1) | 5P-7306 | Housing | 1 |
5P-7305 | Engine Turning Tool | 1 |
Show/hide table
(1) | This Tool is used in the aperture for the electric starting motor. |
Show/hide table
Illustration 1 | g03692044 |
Cylinder and valve location (A) Exhaust valves (B) Inlet valves |
- Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism Cover - Remove and Install" for the correct procedure.
Show/hide table
Illustration 2 g03698915 Typical example - Select an exhaust rocker arm (1). The exhaust rocker arm (1) can be on any cylinder.
- Use Tooling (A) to rotate the crankshaft in the normal direction of rotation until the hydraulic lash adjuster starts to open the exhaust valve. Continue to rotate the crankshaft until the valve has opened to the maximum extent. This is the safe position.
Note: Make temporary marks on the front pulley and the front housing once the engine is in the safe position.
Show/hide table
NOTICE |
---|
Ensure that the crankshaft is located in the safe position before the rocker shaft assembly is installed. |
Caterpillar Information System:
C3.4B Engines for Caterpillar Built Machines Engine Valve Lash - Inspect
C3.4B Engines for Caterpillar Built Machines Glossary of Electronic Control Terms
C3.4B Engines for Caterpillar Built Machines Power Sources
C3.4B Engines for Caterpillar Built Machines Electronic Control System
C3.4B Engines for Caterpillar Built Machines Introduction
CD44B and CD54B Vibratory Asphalt Compactors Maintenance Interval Schedule
CP-533E and CS-533E Vibratory Soil Compactors Maintenance Interval Schedule
415F2, 416F2, 420F2 IT, 420F2 ST, 430F2 IT and 430F2 ST Backhoe Loaders Machine Systems Window Wiper and Wiper Motor (Front) - Remove and Install
14M3 Motor Grader Electrical System Troubleshooting HVAC, Condensate Drainage System
16M Series 3 and 18M Series 3 Motor Graders HVAC, Air Conditioning System
CB64B, CB66B and CB68B Vibratory Asphalt Compactors Water Spray System Filter - Clean
RM500B Reclaimer Mixer Machine Systems Rotor Transmission (Input Shaft, Rotor Transmission Case, and Transmission Planetary) - Remove and Install
Installing Product Link Kits to F2 Series Backhoe Loaders{1408, 7490, 7601, 7603, 7610, 7620} Installing Product Link Kits to F2 Series Backhoe Loaders{1408, 7490, 7601, 7603, 7610, 7620}
CB64B, CB66B and CB68B Vibratory Asphalt Compactors Fuses - Replace
906K, 906M, 907K, 907M, 908K and 908M Compact Wheel Loaders Hoses and Clamps - Replace
Installation of Mechanically Attached Sidebar Protectors on Loader Bucket{6101, 6102, 6817} Installation of Mechanically Attached Sidebar Protectors on Loader Bucket{6101, 6102, 6817}
2015/03/10 An Improved Sideshift Lock Lines are Now Used on Certain 424B Backhoe Loaders {5057, 5484}
C3.4B Engines for Caterpillar Built Machines Diesel Exhaust Fluid Tank - Flush
C3.4B Engines for Caterpillar Built Machines Aftertreatment SCR System Dosing - Test
422F2, 426F2, 428F2, 432F2, 434F2 and 444F2 Backhoe Loaders Maintenance Interval Schedule
G3516 TA Engine ECM - Replace
CB64B, CB66B and CB68B Vibratory Asphalt Compactors Fuel System Primary Filter (Water Separator) - Replace
SE50 VT Asphalt Screed Tamper Bar - Check and Adjust
826K Landfill Compactor, 825K Soil Compactor and 824K Wheel Dozer Engine Supplement Muffler and Mounting - Remove and Install